Check a vehicle VIN check Latest recalls Latest complaints Common problems Rankings Compare vehicles Recall roundups All makes Guides Share your experience
Theme

Vehicle safety record

1988 Oldsmobile Cutlass Problems, complaints & recalls

Owners have filed 74 complaints about the 1988 Oldsmobile Cutlass with NHTSA, most often about the brakes (36) and the body, doors & structure (9). Those complaints describe 5 crashes, 2 fires, 2 injuries and 2 deaths. It is covered by 6 recalls, the latest in April 1997 for the structure. For comparison, the 1987 has 18 and the 1989 has 113.

NHTSA data checked

FFar more problems than a typical Cutlass year, for its age

#11 most complained-about 1988 vehicle

Complaints
74
Recalls
6
Crashes
5
Fires
2
Injuries
2
Deaths
2

Most common 1988 Oldsmobile Cutlass problems

Share of all 74 complaints. One complaint can name more than one area. Tap an area for its complaints and recalls.

1988 Oldsmobile Cutlass recalls 6

Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do

Structure

97V058000676,535 vehicles affected

The problem
Vehicle description: passenger vehicles and mini vans originally sold or currently registered in the following states: connecticut, illinois, indiana, maine, massachusetts, michigan, new hampshire, new jersey, new york, ohio, pennsylvania, rhode island, vermont and wisconsin. The rear cradle bolts pull through the retainers due to corrosion of the retainer. If both bolts pull through, the rear cradle would not longer be supported at these mounting locations and the steering intermediate shaft can separate from the steering gear.
The risk
If this were to occur while the vehicle was in motion, a vehicle crash could result.
The fix
Dealers will replace the rear cradle bolts and retainers.

Wheels

95V11500022,361 vehicles affected

The problem
Cracks develop in the wheel mounting surface. If these cracks become severe enough, the wheel will completely separate from the vehicle.
The risk
If wheel separation occurs while the vehicle is in motion, loss of steering and brake control of the vehicle occurs, and a vehicle crash could result without prior warning.
The fix
Dealers will inspect the manufacturing date codes stamped on each wheel of the vehicle and if a wheel falls within the specified date code range, the dealer will replace that wheel assembly.

Wheels

94V041000198,163 vehicles affected

The problem
Cracks develop in the wheel mounting surface. If these cracks become severe enough, the wheel will completely separate from the vehicle.
The risk
If wheel separation occurs while the vehicle is in motion, loss of steering and brake control of the vehicle occurs, and a vehicle crash could result without prior warning.
The fix
Dealers will inspect the manufacturing codes stamped on each wheel of the vehicle and if a wheel falls within the specified date code range, the dealer will replace that wheel assembly.

Seat belts

90V054000673,000 vehicles affected

The problem
Front shoulder belt guide loop attachment fastener may pull through door mounted anchor plate.
The risk
Seat belt may not sustain loads required by fmvss 210, and in a vehicle accident, the seat belt may not properly restrain a passenger, resulting in increased risk of greater injury to an occupant.
The fix
Replace front shoulder belt guide loop attachment nuts and install new guide cover.

Vehicle speed control

89V1020001,755,897 vehicles affected

The problem
A small nylon bushing in the cruise control servo bail may slip out of place, causing intermittent and unexpected increases in engine speed or dieseling (engine run on with ignition off).
The risk
Servo rod assembly could catch on engine components andresult in a stuck throttle with potential for a vehicle crash.
The fix
Install a new bushing in cruise control servo bail.

Parking brake: linkage and cable

88V1750003,857 vehicles affected

The problem
The parking brake cable may be disconnected from the left rear brake caliper.
The risk
Parking brake cannot be properly applied and vehiclewill not meet the grade holding requirements of fmvss 105.
The fix
Install a retainer on left rear caliper if cable is not already retained with a cotter pin and adjust parking brake system.

What owners say

Be the first Cutlass owner to share.

Problems or none - your experience is exactly what the next buyer is looking for. Write it now

74 complaints about the 1988 Oldsmobile Cutlass

Newest first, as filed with NHTSA by owners. Page 1 of 3.

Steering

Dt*: the contact stated while driving 45 mph the steering went out in the vehicle. The vehicle was pulled off the side of the road without incident. The vehicle was towed to independent repair shop and the rack and pinion was replaced. There is a nhtsa recall, # 03v527000, regarding the steering rack and pinion. The vehicle had the same problems as indicated in the recall; however it is not included in the recall due to the vin. Updated 03/22/06. *Jb

Filed Incident SteeringNHTSA 10151667
SuspensionEngine & coolingSeats & seat beltsCrash1 death

1988 Oldsmobile cutlass- engine cradle and/or front suspensions broke causing loss of control. *La the claim was filed for the deceased consumer. The engine cradle fell. The vehicle was traveling on roadway and ran off the roadway into a ditch and began to roll approx. Three times coming to a rest upside down. The consumer was thrown from the vehicle 20 feet from the vehicle. *Tc

Filed Incident Suspension · Engine and engine cooling · Seat beltsNHTSA 10043188
Body, doors & structureCrash1 injury1 death

Engine support failed (broke) while vehicle was in motion. Impossible steering control, causing vehicle to leave roadway and rolled over 3 times, causing my daughter's death. Also, I reported this devastating event shortly after it occurred and have been unable to obtain any response from any agency. *Ak *jb

Filed Incident StructureNHTSA 10088977
Engine & coolingFire

While driving the vehicle became fully engulfed in fire. *Ph *nm

Filed Incident Engine and engine coolingNHTSA 10057815
BrakesAcceleration & cruise control

Brakes failed, and vehicle started to surge forward.*Ak

Filed Incident Service brakes, hydraulic · Vehicle speed controlNHTSA 8010699
Steering

Consume rwas traveling about 60mph on highwayand without prior warning steering went out, and bolts that held steering column ,fell onto floor. Dealership was aware of problem.*Ak

Filed SteeringNHTSA 895097
Fuel system

Fuel lines are rusting and will need to be replaced. Please provide any additional information/attachments.*Ak

Filed Incident Fuel system, gasolineNHTSA 885408
Fuel systemElectrical systemBody, doors & structure

1.) The drivers side door sags and the hinges are rusty. The door looks as though it will fall off at any time. The passenger door has already fallen off once, I have replaced the hinges. When it fell off, we were stopped, but it almost fell on my cousin's leg. 2.) The car does not start like normal. The vehicle will "turn over" but will not ignite. It usually takes three times to start it. 3.) When the vehicle is in motion, it stutters and nearly stalls. I have spent $600 getting a new ignition moduel, fuel pump, prom chip, map sensor, wire set, fuel filter. It ran well for about 9 months and is now having the same indications of the same problems.

Filed Incident Fuel system, gasoline · Electrical system · StructureNHTSA 741199
Suspension

NO SUMMARY LISTED FOR ABOVE VEHICLE. *AK

Filed Incident SuspensionNHTSA 740422
Body, doors & structure

Consumer lost control. Adjuster discovered that cradle bolts were corroded due to a defctive product. *Ak

Filed StructureNHTSA 878037
Body, doors & structure

Consumer lost control of vehicle, and car was totaled, no warning signs, an adjuster came and said that cradle bolts were corroded due to a defective product. *Ak

Filed Incident StructureNHTSA 878036
Body, doors & structure

Cradle bolts failed prior to recall notice 97v-058, consumer request reimbursement. Nlm

Filed Incident StructureNHTSA 558216
Brakes

When consumer applies brakes pedal is soft. Brakes do not stop vehicle. *Ak

Filed Incident Service brakes, hydraulicNHTSA 875267
Body, doors & structure

Consumer recieved manufacturer's recall o00065-s and took vehicle to dealer for repairs, dealer stated that the recall couldn't be done due to the recall component not being supported by the frame holes and frame, dealer informed consumer in order to do recall the entire frame assembly would need to be replaced at consumer's cost. *Slc

Filed StructureNHTSA 556439
Fuel systemElectrical system

Engine shutdown/no power steering/dangerous situation /elderly driver !! This is a continuous problem and the car has only 50k miles. Two fuel pumps and one module replaced since 1995. The fuel pumps replaced in a one year period. *Ak

Filed Incident Fuel system, gasoline · Electrical systemNHTSA 732078
Wheels & tires

I was driving on the interstate @ 70mph, when the tread on my tire separated. The tire did not go flat or blow completely out. I contacted the store where I bought the tire and was told it was not a tire defect. I still have the tire, for I felt with all the problems surronding firestone tires, this might be another model that is unsafe. I have photos of the damage to my car, I have been unable to get any response from firestone, as I wold like to submit a claim.( Dot number: hyjk4055 tire size: 185-80-13 )

Filed Incident TiresNHTSA 728500
Engine & cooling

While driving vehicle would just go dead. Once going down a hill power went out and there were no brakes. But consumer mangaged to level car off. Consumer has no control over the car. Vehicle would start right back up again. *Ak

Filed Incident Engine and engine coolingNHTSA 859543
Electrical system

Ecm prom had to be replaced 02/01/2000, and at that time we were informed that a service bulletin(88-t-147b) had been issued for this problem in the past. Is it possible for us to request reimbursement from the manufacturer for both the part and labor since we never received the original bulletin and this part had never previously been replaced?*Ak

Filed Electrical systemNHTSA 719309
BrakesCrash1 injury

With light braking the rear brakes locked up at speeds under 15mph. This happened twice, the second time resulting in a crash with vehicle being totaled. *Ak

Filed Incident Service brakes, hydraulicNHTSA 717535
BrakesCrashFire

The rear calipers have locked up several times. They have both been replaced several times. The brakes go on fine, and stop the car great, but they do not release once the brake pedal is released. The master cylinder and brake booster have also been replaced, as has the parking brake cable. Once they I locked, if I turn off the enging and wait for a few minutes, they will eventually release. I have taken the car to several shops, but they are unable to find the problem. This problem has resulted in fire twice, and smoke and totalled rotors on several occasions.

Filed Incident Service brakes, hydraulicNHTSA 715508
Seats & seat belts

Shoulder harness in the rear was added by consumer, however buckle fit at the childs chest area which is a potential safety hazard. Mjs

Filed Seat beltsNHTSA 549477
Electrical system

When driving at any speed the vehicle is stalling and cutting off due to the electrical wires under the dashboard melting. *Ak

Filed Incident Electrical systemNHTSA 851176
Body, doors & structure

A piece of the chassis that is connected to the sway bar broke off. Also, the a-frame on the passenger's side ripped away from the chassis. *Ak

Filed Incident StructureNHTSA 827439
Engine & cooling

The distributor shaft seal has deteriorated, allowing oil to flow down the engine block and cover to the bottom of the car with oil. This has also happened to my parents 1991 oldsmobile cutlass supreme. When I went to my mechanic, he showed me a service form where he just fixed a 1992 olds cutlass supreme 2 days ago for the exact same problem. It seems to me that if you allow oil to cover the bottom of your car, as well as exterior engine components, it may be a fire hazard. I plan on asking other owners with the 2.8 And 3.2 Liter engines if they are having the same problem. Thank you, dan harlett [email protected]. *Ak

Filed Incident Engine and engine coolingNHTSA 701863
SteeringSuspensionTransmission & drivetrain

Recall 97v058000, rear cradle bolts. The recall notice was received and dealer was contacted to remedy the problem. Dealer states various problems associated and caused by the rear cradle bolts, included right cv joint/ right front end alignment/ lower ball joints/weakstruts/ right and left tires in front/rear leaf spring broke from mount support. Also, transmission failed. Dealer cannot duplicate the problem. *Ak

Filed Incident Steering · Suspension · Power trainNHTSA 826726

Oldsmobile Cutlass: every year compared

YearComplaintsRecallsCrashesFiresTop problemGrade
19920400-B
19910800-D
19900600-C
1989113664BrakesF
198874652BrakesF
198718222Seats & seat beltsF
198623313BrakesF
198518332Acceleration & cruise controlF
198416213Engine & coolingF
All Cutlass years

1988 Oldsmobile Cutlass vs rivals

More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.

Own a 1988 Oldsmobile Cutlass? Share your experience.

Your experience goes live straight away and helps every owner and buyer who checks this vehicle. Anonymous, free, no account.

Overall, how would you rate it? *

0/4000 · Please leave out names, phone numbers and your full VIN.

By posting you confirm it's your own, honest experience and agree to the rules. Safety defect? Also report it to NHTSA - that's how recalls start.

Questions about the 1988 Oldsmobile Cutlass

Does the 1988 Oldsmobile Cutlass have any recalls?

Yes - NHTSA lists 6 recalls for the 1988 Oldsmobile Cutlass: structure (April 1997); wheels (June 1995); wheels (March 1995); seat belts (March 1990) and more. Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.

What are the most common problems with the 1988 Oldsmobile Cutlass?

By the complaints owners filed with NHTSA, the most common problem areas are the brakes (36), body, doors & structure (9), electrical system (6).

How many complaints has the 1988 Oldsmobile Cutlass had?

74 complaints have been filed with NHTSA, the first on February 17, 1995 and the latest on March 2, 2006. Of these, 5 describe a crash and 2 a fire, and together they report 2 injuries and 2 deaths.

Is the 1988 Oldsmobile Cutlass a reliable vehicle?

Its Safety Index is 5 out of 100 (grade F: far more problems than a typical Oldsmobile Cutlass year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.

Which Oldsmobile Cutlass years have the most complaints?
What should I do if my 1988 Oldsmobile Cutlass has a problem?

If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.

Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data

Owners helping owners

Know before you drive.

Every experience you share - good or bad - shows on that vehicle's page and helps the next owner and buyer. Two minutes, anonymous.

Share your experience