- The problem
- Federal-mogul is recalling certain replacement control arm assemblies, part numbers k7425, 10945, fa4510x, k7427, 10946, and fa4611x, sold for use on various passenger vehicles listed above. The ball joint on the control arm assembly can fail causing the ball stud to wear through the control arm housing resulting in noise and/or separation of the ball stud from the housing.
- The risk
- If there is a separation of the ball stud from the housing, the driver can loose steering control, possibly resulting in a vehicle crash.
- The fix
- Federal-mogul will notify owners of record and replace the affected control arms free of charge. The safety recall began on january 28, 2011. Owners may contact federal-mogul at 1-877-489-6659.
Vehicle safety record
1999 Chrysler Cirrus Problems, complaints & recalls
Owners have filed 72 complaints about the 1999 Chrysler Cirrus with NHTSA, most often about the transmission & drivetrain (14) and the fuel system (10). Those complaints describe 6 crashes, 2 fires and 6 injuries. It is covered by 7 recalls, the latest in December 2010 for the lower arm. For comparison, the 1998 has 76 and the 2000 has 107.
NHTSA data checked
CAbout as many problems as a typical Cirrus year, for its age
#97 most complained-about 1999 vehicle
- Complaints
- 72
- Recalls
- 7
- Crashes
- 6
- Fires
- 2
- Injuries
- 6
- Deaths
- 0
Most common 1999 Chrysler Cirrus problems
Share of all 72 complaints. One complaint can name more than one area. Tap an area for its complaints and recalls.
1999 Chrysler Cirrus recalls 7
Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do
- The problem
- Qualis automotive is recalling certain aftermarket ball joints sold for use on certain passenger vehicles. The socket may have been excessively hardened which could cause it to crack near the retaining ring groove allowing the ball stud to separate under impact load. The subject ball joints were sold as four part numbers, d10945, d10946, g10945, and g10946. The affected control arms, d10945 and d10946, are stamped with the following dates on the ball joints: 134308, 135708, 100109, 102709, 104109, 105509, 107609, 108909, 110309, 113209, and 116609. The g10945 and g10946 are the same part as the d10945 and d10946 respectively. They are labeled differently depending on the aftermarket customer.
- The risk
- Separation of the ball stud from the socket of the ball joint housing would allow the control arm to collapse and the wheel to fold in causing loss of steering control, possibly resulting in a crash.
- The fix
- Qualis automotive will replace the ball joints free of charge. The safety recall began on november 9, 2009. Owners may contact qualis automotive at 1-800-493-4128.
- The problem
- Import products is recalling 30,351 fuel filters sold to and branded by the affinia group as carquest p/n 86523, napa p/n 3523, and wix p/n 33523 for use as replacement equipment on the vehicles listed above. These filters may develop a leak in the hose assembly and/or connectors due to improperly adhered line connectors.
- The risk
- THIS CONDITION MAY RESULT IN A VEHICLE FIRE.
- The fix
- The affinia group will notify owners and the filters will be replaced free of charge. The safety recall began on august 1, 2009. Owners may contact wix filter return center at 1-704-869-7411 or import products at 1-508-279-8207.
- The problem
- Certain tigas fuel pump modules manufactured between june 1 and september 24, 2006, sold under various brand names and p/nos. These fuel pump modules are sold as aftermarket for use in certain daimlerchrysler vehicles listed above. Silicone material used in manufacture of the flapper valve was out-of-specification, leading to excess swell of the flapper valve restricting the flow of fuel to the fuel pump module.
- The risk
- Fuel restriction could result in loss of power and/or engine stall, possibly resulting in a vehicle crash.
- The fix
- Ti automotive will notify owners and replace the defective fuel pump modules free of charge. The recall began on october 6, 2006. Owners may contact ti automotive toll-free at 1-877-461-1834.
- The problem
- On certain passenger vehicles equipped with 2.4 Liter engines, the high pressure power steering hose may prematurely heat age and develop a leak.
- The risk
- Power steering fluid leakage in the presence of an ignition source may result in an underhood fire.
- The fix
- Dealers will replace the high pressure power steering hose free of charge. The the recall began on april 10, 2006. Owners may contact daimlerchrysler at 1-800-853-1403.
- The problem
- On certain passenger vehicles, the floor shifter ignition-park interlock may fail and allow the shifter to be moved out of the park position with the key removed. An inoperative interlock may also allow the key to be removed when the shifter has not been placed in the park position.
- The risk
- Either circumstance may result in the vehicle rolling away without warning.
- The fix
- Dealers will install a new load-limiting push rod into the floor shifter lever of the affected vehicles. Owner notification began on june 14, 2004. Owners should contact daimlerchrysler at 1-800-853-1403.
- The problem
- Vehicle description: passenger vehicles. The right rear brake tube can contact the exhaust system clamp and wear a hole in it.
- The risk
- Daimlerchrysler recall no. 843. If this happens, the tube could leak, reducing the effectiveness of one-half of the diagonally split braking system, and resulting in longer stopping distances.
- The fix
- Dealers will inspect the brake tubes for visible evidence of contact with the exhaust system clamp. If the tube shows evidence of contact, it will be replaced. If no evidence of contact exists, the tube will be fastened with a clip.
What owners say
Problems or none - your experience is exactly what the next buyer is looking for. Write it now
72 complaints about the 1999 Chrysler Cirrus
Newest first, as filed with NHTSA by owners. Page 1 of 3.
Air bags failed to deploy during wreck. Multiple both axle and wheel bearings failures
This is second time my battery has died and l am still unable to jump the thing. Something is wrong that the mechanics or dealerships aren't telling me . *Tr
1999 Chrysler cirrus, will not start after rain. There is no distributor and I feel that it could be a problem with the fuel system. I pump the gas and try to turn it over it just cranks sometimes it does eventually start. I have missed days of work. So when ever it rains I am always worried, this happens often. *Tr
The distributor has gone out twice (2x) on my 1999 chrysler cirrus. The first time was in 2007 while I was sitting in a car wash. I thought perhaps some water had splashed in and shorted something out. So I didn't report it. But the second time was on friday, may 29th. We were driving on the i-210 freeway in the carpool lane - near azusa, ca. Suddenly the car lost all power and I had to pull across 5 lanes of traffic in order to safely get off the freeway. It was very scary and very dangerous. If I had not been...
Read the full complaint
able to pull over, the car would just have stopped dead on a busy freeway on the friday afternoon of the memorial day weekend. I asked the mechanic at clippinger chrysler in covina where we had the car towed if the distributor went out often on their cars. He said it was "rare." I think that the fact that it has gone out twice on my car in the past 2 years is very strange and could constitute a serious defect. *Tr
About 2 years ago, my car began stuttering and stalling out with no warning. The oil light repeated flashes on, the check engine light flashes and then stays on, and the car wont start or just cuts off. The transmission speed sensor was replaced. The transmission was replaced. The oil was changed. This past 3 months alone, it has been at the service department 6 times for this same problem. I am now being told that I need a tune-up, which will cost $700, then the egr needs replaced, and a few other things. ...
Read the full complaint
However, when the mechanic had it last week, he could not find anything wrong with it. I have found out that the cirrus vehicles have this same problems that I am having. I was on my way to the mall via the parkway when the car stalled out. Luckily traffic was slow because if I was on the parkway and it stalled out, my sister and I could have gotten killed. There is no predetermined time when these problems occurred. The car only has 89500 miles on it. I have all of my original repair papers. Proper maintenance has always been done on my car. When it works, it is great. Unfortunately, I just never know when it is going to not start. *Tr
I have a 1999 chrysler cirrus. My wife took the car for the day 10/15/08, she called me at work to say the brakes were making a very loud grinding noise. The next day I drove the car to the dealer to have the brakes serviced. On the way over, the brake pads completely stopped functioning. I had to down shift to stop. I drove at 10 mph or slower the last mile to the dealer. They told me the rotors needed to be replaced along with the brakes. This car had no brakes. What troubles me, is that the brake pads had no...
Read the full complaint
wear indicators on them. Had I heard the screeching of the indicators, I would have had the pads replaced sooner. I had no idea the pads was that bad. A few days earlier, I was in rhode island to visit my daughters. I was traveling at highway speeds. This could have caused a bad accident had the brakes failed then. The dealer told me that not all brake pads have these wear indicators. I think this is a safety issue that should be addressed. The cost of including these on all brake pads couldn't be that much. Pass the cost on if they have to. *Tr
I currently own a 1999 chrysler cirrus v6. Auto is equipped with a 41te automatic transmission with 104,000 miles on it. According to al web sites I have come to find that the 41te automatic transmission has proven to be an unreliable unit resulting in premature failure and bearing failure. Chrysler has refused to acknowledge the defect. As of this writing the pinion bearings have failed in my vehicle and chrysler has refused to repair as this is an ongoing problem with this transmission for which the...
Read the full complaint
manufacturer denies an responsibility. There are thousands of people like me out there with no recourse. Estimated repair cost $2,000.00. 1999 Chrysler cirrus v6 any assistance you can provide would be greatly appreciated as there are many other people like me out there. *Tr
Tl*the contact owns a 1999 chrysler cirrus. The contact had a passenger in the front passenger seat of the vehicle, but the latch plate could not be secured into the seat belt buckle. Two weeks prior to the failure, the seat belt was functioning properly. He called the manufacturer, nhtsa, and spoke with someone at chrysler. He also scheduled an appointment with a local dealer. The manufacturer advised him to obtain the cost for the repairs and have the dealer identify the failure component. Once at the...
Read the full complaint
dealer, it was determined that the front passenger seat belt buckle was the cause of the failure. The failure mileage was 47,000 and current mileage was 47,050. Updated 09/15/08 *bf updated 09/22/08. *Jb
I have a 1999 dodge durango going in for it's second transmission replacement at a cost of $1,900,the car has 108k miles. *Tr
Tl*the contact owns a 1999 chrysler cirrus. While driving 35 mph, the engine failed along with the power steering and brakes. A message in the instrument control panel displayed "no bus". The dealer stated that the cause of the failure was unknown. No repairs were made. The dealer currently has possession of the vehicle. The current and failure mileages were 99,500. Updated 11/06/07. *Jb
Tl*the contact owns a 1999 chrysler lhs. The contact took the vehicle to have the tires changed. The mechanic noticed that the tires were wearing too quickly and stated that the bolts inter-rack was a quarter of an inch unscrewed. The mechanic determined that the vehicle was unsafe to drive. The contact is not the original owner of the vehicle and stated that it was previously in two minor crashes. The current and failure mileages were 124,000. The consumer stated this is the 3rd rack and pinion installed on this vehicle in a 3 year period. The consumer stated the rack and pinion is replaced every 20,000 miles. Updated 09/05/07 *tr
Tl* - the contact called regardingthe 1999 chrysler cirrus. The contact stated that while turning the wheel to the left she heard a winding noise. She was constantly having to put power steering fluid in the vehicle. There were no warning indicators. The failure mileage was 146,276. The contact stated there was a recall on the power steering, but she was advised by a chrysler dealer that this vehicle was not part of the recall due to the vin. *Ak updated 03/30/07. *Jb
Dt*: the contact stated while driving 25 mph the steering column locked. The manufacturer was alerted however no repairs have been made. Updated 3/28/2006 - *nm
Brakes failed at approx 30,000 miles with no indication (brake noises, brake pressure, nothing) resulting in 30-35 mile collision at stop light extensive vehicle damage. Got ticketed, lost case. 30,000 Miles-perfect.*Jb
1. Engine looses power and shuts down while driving. 2. Engine looses power while driving and restarts by itself. 3. Engine looses power while driving and does not restart for hours. 4. Engine is reading no codes, check engine light does not flash. A diagnostic test will not show anything is wrong. This car is a 1999 chrysler cirrus lxi. *Jb
(1)A 1999 chysler cirrus was run to near empty on gas. The gauge read between a quarter tank and empty on the way to the gas station. Upon arriving at the gas station the tank was filled. After filling with gas, I proceeded to try after start my car and it failed to function. My husband who is a self-employeed mechanic thought it to be a problem with the fuel pump. (2)Upon removal of the gas tank unit and the fuel pump assembly, we found there to be a possible hazard with the wiring harness located inside of...
Read the full complaint
the gas tank unit itself. The wires actually began to melts together instead of disturbing the fuel pump fuse located nuetrally on the fuse panel in another area of the car. We feel that if the melting of the wires had been more intense that there could have been an explosion due to the mixture of heat and combustable gases/fumes. (3)The fuel pump was replaced with a new unit and installed.
Oil light in well-maintained 1999 3.5L chrysler 300m came on at 68,565 miles in front of dealer, where car was left. Engine making no unusual noises when shut off. Informed that when restarted for diagnostic testing, engine was making noises indicating substantial top and bottom end damage, necessitating replacement for $5,180.22. Was given chrysler's customer service number by dealer, but chrysler states there is nothing they would do about it since it was no longer under warranty. This is clearly premature engine failure for which the manufacturer should bear some responsibility. Vehicle had also had premature steering rack wear several years prior that was repaired under warranty. *Jb
I have a 300m, and I have two cracks on my passenger airbag. *Ak
I crashed into sand barrels after I was cut off the road and using my best judgement, tried to utilize the exit. The center to left of my 1999 chrysler 300m was crushed and the car was totalled at over 80 percent damage. I received only whiplash and a bruise from the seatbelt. So where were the airbags? Chrysler claimed, during a phone call, that airbags are smarter and the computer senses the extent of necessity for airbag deployment. When the collision shop declared the auto a total loss at first sight,...
Read the full complaint
along with the allstate appraisor, I had to question the validity of the chyrsler statement. Chrysler says that the computer can estimate the time that the car goes from (i.E) 60 to zero and makes the decision to deploy. Other cars in the collsion lot had similar damage and their airbags were hanging out of their dashboards.*Ak
While driving any speed, the transmission would cause the vehicle to jerk forward. The dealership was notified, but did not resolve the problem. The cause was not determined. Please provide more information.
I was turning into my driveway when I lost steering. The vehicle was towed to gas station for repair. Both bolts attaching the inner tie rods to the rack and pinion steering mechanism had sheared. The bolts were replaced. I have the old bolts.*Ak
Nhtsa recall 04v021000 on the floor shift ignition park interlock. After having a new load-limiting push rod into the floor shifter lever installed, the check engine light appeared on the dashboard. Consumer was also having problem shifting gears. The vehicle was taken back to the dealer for inspection. The mechanic could not duplicate the problem please provide further details. *Jb
Every eight to ten thousand miles the rotors warped. While stopping at 70 mph steering wheel felt as if it was going to come right out of consumer's hands. Consumer stated that chrysler manufactured the vehicle with the wrong part. The brakes were worked on three times. But, problem recurred.*Ak
While driving, the check engine light appeared on the dashboard and remained on. The vehicle was taken to the dealer and the mechanic replaced a sensor, however the problem recurred. While driving 50 mph, the vehicle stalled three times. The consumer restarted the vehicle and drove it to the dealer for inspection. *Ak *sc *jb
While driving the engine light illuminated. The vehicle was taken to the dealer, who found that fuel vapors were leaking from the gas tank. The dealer replaced the fuel tank seals, but the engine light continued to illuminate. The vehicle was taken back to the dealer where the mechanic determined that the vehicle should not be driven because of safety precautions and recommended replacing the fuel tank. *Ak the seal was replaced again however there was a small indentation where tank seal fit. *Sc *jb
Chrysler Cirrus: every year compared
All Cirrus years1999 Chrysler Cirrus vs rivals
| Vehicle | Complaints | Recalls | Grade | |
|---|---|---|---|---|
| 1999 Chrysler Cirrus | 72 | 7 | C | |
| 1999 Chrysler Town & Country | 372 | 0 | C | Compare |
| 1999 Chrysler 300M | 351 | 4 | F | Compare |
| 1999 Chrysler Concorde | 333 | 5 | D | Compare |
| 1999 Chrysler Sebring | 172 | 9 | C | Compare |
| 1999 Chrysler LHS | 164 | 4 | F | Compare |
| 1999 Chrysler Sebring Convertible | 91 | 3 | F | Compare |
| 1999 Chrysler New Yorker | 1 | 0 | A | Compare |
More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.
Questions about the 1999 Chrysler Cirrus
Does the 1999 Chrysler Cirrus have any recalls?
Yes - NHTSA lists 7 recalls for the 1999 Chrysler Cirrus: lower arm (December 2010); lower ball joint (October 2009); equipment (July 2009); fuel pump (October 2006) and more. Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.
What are the most common problems with the 1999 Chrysler Cirrus?
By the complaints owners filed with NHTSA, the most common problem areas are the transmission & drivetrain (14), fuel system (10), engine & cooling (10).
How many complaints has the 1999 Chrysler Cirrus had?
72 complaints have been filed with NHTSA, the first on October 29, 1998 and the latest on October 5, 2022. Of these, 6 describe a crash and 2 a fire, and together they report 6 injuries and 0 deaths.
Is the 1999 Chrysler Cirrus a reliable vehicle?
Its Safety Index is 53 out of 100 (grade C: about as many problems as a typical Chrysler Cirrus year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.
Which Chrysler Cirrus years have the most complaints?
1995 (382), 1996 (174), 2000 (107). See every Chrysler Cirrus year compared.
What should I do if my 1999 Chrysler Cirrus has a problem?
If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.
Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data