- The problem
- Federal-mogul is recalling certain replacement control arm assemblies, part numbers k7425, 10945, fa4510x, k7427, 10946, and fa4611x, sold for use on various passenger vehicles listed above. The ball joint on the control arm assembly can fail causing the ball stud to wear through the control arm housing resulting in noise and/or separation of the ball stud from the housing.
- The risk
- If there is a separation of the ball stud from the housing, the driver can loose steering control, possibly resulting in a vehicle crash.
- The fix
- Federal-mogul will notify owners of record and replace the affected control arms free of charge. The safety recall began on january 28, 2011. Owners may contact federal-mogul at 1-877-489-6659.
Vehicle safety record
1997 Chrysler Cirrus Problems, complaints & recalls
Owners have filed 76 complaints about the 1997 Chrysler Cirrus with NHTSA, most often about the brakes (12) and the engine & cooling (12). Those complaints describe 9 crashes, 7 fires and 5 injuries. It is covered by 8 recalls, the latest in December 2010 for the lower arm. For comparison, the 1996 has 174 and the 1998 has 76.
NHTSA data checked
CAbout as many problems as a typical Cirrus year, for its age
#78 most complained-about 1997 vehicle
- Complaints
- 76
- Recalls
- 8
- Crashes
- 9
- Fires
- 7
- Injuries
- 5
- Deaths
- 0
Most common 1997 Chrysler Cirrus problems
Share of all 76 complaints. One complaint can name more than one area. Tap an area for its complaints and recalls.
1997 Chrysler Cirrus recalls 8
Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do
- The problem
- Qualis automotive is recalling certain aftermarket ball joints sold for use on certain passenger vehicles. The socket may have been excessively hardened which could cause it to crack near the retaining ring groove allowing the ball stud to separate under impact load. The subject ball joints were sold as four part numbers, d10945, d10946, g10945, and g10946. The affected control arms, d10945 and d10946, are stamped with the following dates on the ball joints: 134308, 135708, 100109, 102709, 104109, 105509, 107609, 108909, 110309, 113209, and 116609. The g10945 and g10946 are the same part as the d10945 and d10946 respectively. They are labeled differently depending on the aftermarket customer.
- The risk
- Separation of the ball stud from the socket of the ball joint housing would allow the control arm to collapse and the wheel to fold in causing loss of steering control, possibly resulting in a crash.
- The fix
- Qualis automotive will replace the ball joints free of charge. The safety recall began on november 9, 2009. Owners may contact qualis automotive at 1-800-493-4128.
- The problem
- Certain airtex fuel pump modules, p/nos. E7089m, e7094m, e7113m, and e7129m, manufactured between june 1 and september 24, 2006. These fuel pump modules were sold as aftermarket for use in certain daimlerchrysler vehicles listed above. Silicone material used in manufacture of the flapper valve was out-of-specification, leading to excess swell of the flapper valve restricting the flow of fuel to the fuel pump module.
- The risk
- Fuel restriction could result in loss of power and/or engine stall, possibly resulting in a vehicle crash.
- The fix
- Airtex will notify owners and replace the defective fuel pump modules free of charge. The recall began on october 18, 2006. Owners may contact airtex toll-free at 1-866-867-3759.
- The problem
- Certain tigas fuel pump modules manufactured between june 1 and september 24, 2006, sold under various brand names and p/nos. These fuel pump modules are sold as aftermarket for use in certain daimlerchrysler vehicles listed above. Silicone material used in manufacture of the flapper valve was out-of-specification, leading to excess swell of the flapper valve restricting the flow of fuel to the fuel pump module.
- The risk
- Fuel restriction could result in loss of power and/or engine stall, possibly resulting in a vehicle crash.
- The fix
- Ti automotive will notify owners and replace the defective fuel pump modules free of charge. The recall began on october 6, 2006. Owners may contact ti automotive toll-free at 1-877-461-1834.
- The problem
- On certain passenger vehicles, the floor shifter ignition-park interlock may fail and allow the shifter to be moved out of the park position with the key removed. An inoperative interlock may also allow the key to be removed when the shifter has not been placed in the park position.
- The risk
- Either circumstance may result in the vehicle rolling away without warning.
- The fix
- Dealers will install a new load-limiting push rod into the floor shifter lever of the affected vehicles. Owner notification began on june 14, 2004. Owners should contact daimlerchrysler at 1-800-853-1403.
- The problem
- Vehicle description: passenger vehicles equipped with automatic transmissions. The adjustment of the cable connecting the console shifter mechanism to the ignition key can cause a trapped key condition which can result in a low force required to depress the shift button. A combination of applying a mis-adjusted release button with a low force attempt to shift out of park with the key in the locked position, can break the connecting pin in the shifter.
- The risk
- If this happens, the "ignition-park" interlock system will be nonfunctional.
- The fix
- Dealers will inspect for proper operation of the system. Any vehicles that are not functional after the inspection will have the shift mechanism and cable replaced with a "self-adjusting" design.
- The problem
- Vehicle description: passenger vehicles. The lower control arm ball joint can separate due to loss of lubrication.
- The risk
- Separation of the ball joint could cause a loss of steering control increasing the risk of a vehicle crash.
- The fix
- Dealers will inspect the ball joint end housing cover seal for leakage with a high pressure air tester and the rubber boot will be visually inspected for damage. If the cover seal leaks or the boot is damaged, the lower control arm will be replaced.
- The problem
- Vehicle description: passenger vehicles. The secondary hood latch spring can disengage from its retention hole if the hood is slammed shut.
- The risk
- If this condition occurs simultaneously without engaging the primary latch, the hood would not be restrained increasing the risk of a vehicle crash.
- The fix
- Dealers will replace the secondary hood latch spring with a longer end hook spring.
What owners say
Problems or none - your experience is exactly what the next buyer is looking for. Write it now
76 complaints about the 1997 Chrysler Cirrus
Newest first, as filed with NHTSA by owners. Page 1 of 4.
At first I heard a squeaking noise that gradually turned into a grinding noise. After having my brake pads replaced and front driver side caliper replaced, the grinding noise turned into a metal on metal grind with a peculiar metal smell which resulted in something ceasing up (only way to describe how tight the tires were rolling and how tight the steering was). It was the lower arm and ball joint separating from each other, all of this was discovered while driving down a city street at a speed of 20 mph, we were able to access the problem better when we jacked up the front end and removed the tire and brakes on the driver front side.
Tl* the contact owns a 1997 chrysler cirrus. The contact stated that while making a right turn, the rear passenger door swung open abnormally. The contact had to screw in the bolt that held the latch into place. The contact was concerned with the possibility of someone falling from the vehicle. The vehicle was not repaired. The vin was not available. The failure mileage was 130,000.
Tl*the contact owns a 1997 chrysler cirrus. The light on the odometer gauge on the instrument control panel stopped working. Shortly afterwards, the entire lighting on the instrument control panel failed. The horn also began blowing without application. The vehicle was taken to the dealer, and they replaced the steering column along with the horn switch. Two weeks after the repair the fuse failed when using the horn. The dealer replaced the ignition switch, but upon further inspection she noticed that the crank...
Read the full complaint
shaft position sensor had melted. The contact stated that the failure was electrical since none of the repairs have remedied the failure, and the vehicle continued to stall without prior warnings. The failure mileage was under 45,000 . The current was 99,877.
I have a 1997 jeep grand cherokee. It has the "wobble of death", so called due to its violent shaking of the front end. I have searched it online and found many cases of the same. I am aware that the vehicle is over 10 years old, but the manufacture has been well aware of the problem. The "wob" has affected vehicles as old as 1994. I am not sure if there is anything that can be done but I feel like I need to try. *Tr
My car is a recall an like to know were can I take it to get fixed. *Tr
Owned a 1997 chrysler cirrus. Put car in reverse to back out of driveway when car accelerated to an incredible speed within seconds. Car shot out of driveway, across street into neighbors home and garage. Car has indication of continued acceleration after impact with right front tire showing the treads no longer exist. Car was totaled and home/garage damage was over $12,000. Thank god! No one was injured or killed! My family and I will never own another chrysler again! *Tr
Tl*the contact owns a 1997 chrysler. The model was unavailable. The contact discovered nhtsa campaign id number 98v184000 (fuel system, gasoline:fuel injection system). She took the vehicle to the dealer and they claimed to have already performed the recall repair. The contact stated that the failure has not been repaired because the fuel rail is leaking. The dealer stated that the fuel rail needed to be replaced, but will not make the replacement. The current and failure mileages were 112,154. Updated 3/25/08 *cn the dealer stated there was a rubbing noise when turning and vehicle needs right wheel bearings. Updated 03/25/08 *tr
Steering is very loose. The car a 1997 chrysler lhs wanders from lane to lane and needs constant steering corrections. This is not the first time. We had the same condition fixed about 3 years ago. *Ak
Tl*- the contact parked her 1997 chrysler cirrus in the driveway, removed the keyes and approximately 30-45 seconds later the vehicle rolled out of the parking lot and crashed into the neighbors carport. The vehicle was parked on a flat surface, and emergency brake was not engaged. The road conditions were dry. The contact stated that the vehicle was taken to the dealership to be repaired due to a recall notice. The dealership advised the contact that they replaced the shifter plunger. The contact is still was having the same problem the vehicle. The current mileage was 10,4000 miles. *Ak
Dt*: the contact stated the vehicle stalled at various speeds, without warning. The vehicle restarted after 3 to 4 minutes. The dealership was unable to duplicate the problem, but cleaned the crankshaft in a repair attempt, but the vehicle continued to stall. Updated 10/25/06. *Jb
Transmission cooler line leak. Potential of fire or loss of drive ability of car. There have been three (3) failures of the same part. 10/21/98 And 4/29/04 and again today 7/11/06. *Nm
Dt*: the contact stated while driving at various speeds the cruise control would not disengage. The vehicle was pulled to the side of the road and the ignition was turned off to stop the vehicle. Although the dealer and manufacturer were alerted, no appointment was made for inspection.
Abs warning light came on. Brought car to dealership for diagnosis. Diagnosis showed system relay output circuit code. Testing showed faulty power distribution center due to corrosion. Proper repair is replacement of power distribution center and harness. Service center found part is no longer manufactured. Service center conducted nationwide parts search to no avail. As a consequence abs system is now non-functional. *Nm
Both tie rods on the left rear tire broke causing the tire to lock up. Which caused loss of control of the car sending the car into a ditch. Front end of car stopped in ditch and rear then came over landing upside down. None of the air bags empolyed.
C AR NOT BRAKING IN A TIMELY MANNER
Upon taking the vehicle in for recall repairs for the trans axle, the consumer started to experience other problems, such as dropping gears, and cutting off intermittently. The consumer took the vehicle to the dealer four times, and the dealer replaced the computer. However, the problem had not been rectified as of yet. *Ak *bf *nm as of april 5, 2005, the vehicle still exhibited the same problem. Recall campaign# 98v183000 & 04v021000. *Ak *tt the idle was re-adjusted. *Sc
The transmission seized while going 35 mph and if I didn't have on my seat belt, I would have been thrown through the windshield. It was if someone threw my car into park while going 35 mph.
Contact stated: contact has had to put two ball joints on this vehicle ,a left ball joint and a right ball joint. When he parked the car he heard a bang. The wheels would be on an angle because the vehicle was a front wheel drive.
Vehicle was parked in a parking garage and without cause the vehicle busted into flames. The parking attendant notified the fire department. After extinguishing the fire the fire department stated that the cause was electrical. *Ak *tt
The vehicle tends to hesitate and move when it is put into drive preventing the vehicle from traveling while on the road. Manufacturer was notified by owner.
Automatic transaxle floor shifter moves from park back and forth without depressing the detent button. *Bf the dealer failed to correct the recall problem. The ignition would become trapped once in while. After gently wiggling it, the key would snap out and operate properly, staying in park and allowing the key to be removed. Recall#98v183000 *sc *jb
When driving in inclement weather transmission malfunctioned. As a result, vehicle came out of gear. *Ak
While driving consumer made a turn and the vehicle stopped. After being towed dealer stated the engine was defective and needed to be replaced. The manufacture wanted the consumer to provide oil change records.*Ak
When driving at stop and go brakes went down to the floor. Consumer took the vehicle to the dealer, who bled the brakes, and test drove the vehicle. Told consumer that there wasd nothing wrong. Later, consumer was driving and the brakes continued to go to the floor. Consumer felt insecure when driving this vehicle. *Ak
Experienced problems with transmission. *Bf the a/c evaporated coil needed to be replaced by the consumer after 42920 miles. The consumers vehicle started leaking oil. The consumer put the vehicle in reverse and proceeded to back out of the driveway. The consumer put the car in drive to drive away after backing and the vehicle continued to go in reverse. The vehicle was taken to the mechanic for service an was found that the pin in the differential had come loose puncturing the transmission case causing rapid fluid loss. The entire transmission had to be replaced. *Tc
Chrysler Cirrus: every year compared
All Cirrus years1997 Chrysler Cirrus vs rivals
| Vehicle | Complaints | Recalls | Grade | |
|---|---|---|---|---|
| 1997 Chrysler Cirrus | 76 | 8 | C | |
| 1997 Chrysler Town & Country | 399 | 0 | C | Compare |
| 1997 Chrysler Sebring | 294 | 11 | D | Compare |
| 1997 Chrysler Concorde | 141 | 2 | C | Compare |
| 1997 Chrysler LHS | 86 | 2 | D | Compare |
| 1997 Chrysler Lebaron | 2 | 0 | A | Compare |
| 1997 Chrysler New Yorker | 2 | 1 | B | Compare |
| 1997 Chrysler Fifth Avenue | 2 | 0 | A | Compare |
More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.
Questions about the 1997 Chrysler Cirrus
Does the 1997 Chrysler Cirrus have any recalls?
Yes - NHTSA lists 8 recalls for the 1997 Chrysler Cirrus: lower arm (December 2010); lower ball joint (October 2009); fuel pump (November 2006); fuel pump (October 2006) and more. Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.
What are the most common problems with the 1997 Chrysler Cirrus?
By the complaints owners filed with NHTSA, the most common problem areas are the brakes (12), engine & cooling (12), transmission & drivetrain (11).
How many complaints has the 1997 Chrysler Cirrus had?
76 complaints have been filed with NHTSA, the first on December 23, 1996 and the latest on September 18, 2017. Of these, 9 describe a crash and 7 a fire, and together they report 5 injuries and 0 deaths.
Is the 1997 Chrysler Cirrus a reliable vehicle?
Its Safety Index is 47 out of 100 (grade C: about as many problems as a typical Chrysler Cirrus year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.
Which Chrysler Cirrus years have the most complaints?
1995 (382), 1996 (174), 2000 (107). See every Chrysler Cirrus year compared.
What should I do if my 1997 Chrysler Cirrus has a problem?
If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.
Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data