Check a vehicle VIN check Latest recalls Latest complaints Common problems Rankings Compare vehicles Recall roundups All makes Guides Share your experience
Theme

Vehicle safety record

1996 Chrysler Cirrus Problems, complaints & recalls

Owners have filed 174 complaints about the 1996 Chrysler Cirrus with NHTSA, most often about the engine & cooling (41) and the brakes (25). Those complaints describe 10 crashes, 5 fires and 11 injuries. It is covered by 11 recalls, the latest in December 2010 for the lower arm. For comparison, the 1995 has 382 and the 1997 has 76.

NHTSA data checked

DMore problems than a typical Cirrus year, for its age

#35 most complained-about 1996 vehicle

Complaints
174
Recalls
11
Crashes
10
Fires
5
Injuries
11
Deaths
0

Most common 1996 Chrysler Cirrus problems

Share of all 174 complaints. One complaint can name more than one area. Tap an area for its complaints and recalls.

1996 Chrysler Cirrus recalls 11

Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do

Suspension: lower arm

10E05900022,689 vehicles affected

The problem
Federal-mogul is recalling certain replacement control arm assemblies, part numbers k7425, 10945, fa4510x, k7427, 10946, and fa4611x, sold for use on various passenger vehicles listed above. The ball joint on the control arm assembly can fail causing the ball stud to wear through the control arm housing resulting in noise and/or separation of the ball stud from the housing.
The risk
If there is a separation of the ball stud from the housing, the driver can loose steering control, possibly resulting in a vehicle crash.
The fix
Federal-mogul will notify owners of record and replace the affected control arms free of charge. The safety recall began on january 28, 2011. Owners may contact federal-mogul at 1-877-489-6659.

Suspension: lower ball joint

09E0560005,787 vehicles affected

The problem
Qualis automotive is recalling certain aftermarket ball joints sold for use on certain passenger vehicles. The socket may have been excessively hardened which could cause it to crack near the retaining ring groove allowing the ball stud to separate under impact load. The subject ball joints were sold as four part numbers, d10945, d10946, g10945, and g10946. The affected control arms, d10945 and d10946, are stamped with the following dates on the ball joints: 134308, 135708, 100109, 102709, 104109, 105509, 107609, 108909, 110309, 113209, and 116609. The g10945 and g10946 are the same part as the d10945 and d10946 respectively. They are labeled differently depending on the aftermarket customer.
The risk
Separation of the ball stud from the socket of the ball joint housing would allow the control arm to collapse and the wheel to fold in causing loss of steering control, possibly resulting in a crash.
The fix
Qualis automotive will replace the ball joints free of charge. The safety recall began on november 9, 2009. Owners may contact qualis automotive at 1-800-493-4128.

Fuel system: fuel pump

06E09100024,358 vehicles affected

The problem
Certain airtex fuel pump modules, p/nos. E7089m, e7094m, e7113m, and e7129m, manufactured between june 1 and september 24, 2006. These fuel pump modules were sold as aftermarket for use in certain daimlerchrysler vehicles listed above. Silicone material used in manufacture of the flapper valve was out-of-specification, leading to excess swell of the flapper valve restricting the flow of fuel to the fuel pump module.
The risk
Fuel restriction could result in loss of power and/or engine stall, possibly resulting in a vehicle crash.
The fix
Airtex will notify owners and replace the defective fuel pump modules free of charge. The recall began on october 18, 2006. Owners may contact airtex toll-free at 1-866-867-3759.

Fuel system: fuel pump

06E08800039,243 vehicles affected

The problem
Certain tigas fuel pump modules manufactured between june 1 and september 24, 2006, sold under various brand names and p/nos. These fuel pump modules are sold as aftermarket for use in certain daimlerchrysler vehicles listed above. Silicone material used in manufacture of the flapper valve was out-of-specification, leading to excess swell of the flapper valve restricting the flow of fuel to the fuel pump module.
The risk
Fuel restriction could result in loss of power and/or engine stall, possibly resulting in a vehicle crash.
The fix
Ti automotive will notify owners and replace the defective fuel pump modules free of charge. The recall began on october 6, 2006. Owners may contact ti automotive toll-free at 1-877-461-1834.

Power train: floor shift

04V0210002,315,768 vehicles affected

The problem
On certain passenger vehicles, the floor shifter ignition-park interlock may fail and allow the shifter to be moved out of the park position with the key removed. An inoperative interlock may also allow the key to be removed when the shifter has not been placed in the park position.
The risk
Either circumstance may result in the vehicle rolling away without warning.
The fix
Dealers will install a new load-limiting push rod into the floor shifter lever of the affected vehicles. Owner notification began on june 14, 2004. Owners should contact daimlerchrysler at 1-800-853-1403.

Power train: park / neutral start interlock switch

98V183000685,000 vehicles affected

The problem
Vehicle description: passenger vehicles equipped with automatic transmissions. The adjustment of the cable connecting the console shifter mechanism to the ignition key can cause a trapped key condition which can result in a low force required to depress the shift button. A combination of applying a mis-adjusted release button with a low force attempt to shift out of park with the key in the locked position, can break the connecting pin in the shifter.
The risk
If this happens, the "ignition-park" interlock system will be nonfunctional.
The fix
Dealers will inspect for proper operation of the system. Any vehicles that are not functional after the inspection will have the shift mechanism and cable replaced with a "self-adjusting" design.

Suspension: lower ball joint

97V201000599,000 vehicles affected

The problem
Vehicle description: passenger vehicles. The lower control arm ball joint can separate due to loss of lubrication.
The risk
Separation of the ball joint could cause a loss of steering control increasing the risk of a vehicle crash.
The fix
Dealers will inspect the ball joint end housing cover seal for leakage with a high pressure air tester and the rubber boot will be visually inspected for damage. If the cover seal leaks or the boot is damaged, the lower control arm will be replaced.

Structure: hinge and attachments

97V095000219,000 vehicles affected

The problem
Vehicle description: passenger vehicles. The secondary hood latch spring can disengage from its retention hole if the hood is slammed shut.
The risk
If this condition occurs simultaneously without engaging the primary latch, the hood would not be restrained increasing the risk of a vehicle crash.
The fix
Dealers will replace the secondary hood latch spring with a longer end hook spring.

Service brakes: master cylinder

96V075000151,800 vehicles affected

The problem
The brake master cylinder can leak brake fluid due to a damaged double lip rear piston seal.
The risk
Brake fluid leakage can result in diminished effectiveness of one half of the split brake system. The instrument panel warning light(s) will signal system impairment prior to partial brake system loss.
The fix
Dealers will replace the rear brake master cylindr piston assembly.
The problem
Corrosion of the abs hydraulic control unit can cause the solenoid valves to stick in the open position.
The risk
If either front wheel valve sticks, the vehicle would swerve from a straight stop when the brakes are applied.
The fix
Dealers will install a plate and silicone grease injected into the solenoid cavity to eliminate the potential for this condition.

Engine and engine cooling: gasoline

96V00600040,000 vehicles affected

The problem
In certain vehicles, the engine cylinder head oil galley plug does not seal properly and engine cylinder head oil is not adequately retained.
The risk
Inadequate sealing and retention of the plug can result in oil leakage which could cause a fire in the engine compartment.
The fix
Dealers will install an expansion plug and retaining bracket over the cylinder head oil galley plug.

What owners say

Be the first Cirrus owner to share.

Problems or none - your experience is exactly what the next buyer is looking for. Write it now

174 complaints about the 1996 Chrysler Cirrus

Newest first, as filed with NHTSA by owners. Page 1 of 7.

SuspensionElectrical systemEngine & cooling

My front tires feel like they are going to break off the vehicle due to the lower ball joints,steering control arm, inner and outer tie rods; accelerates all by itself. Will not lock shifter with key out of ignition. Ecm is faulty because it shuts the lights off,turns engine,all lights, off . Unpredictably! Seat belts do not engage when stopping. If I were to be critically injured because of malfunctioning of said vehicle? Who would take responsibility of my safety and well being? This all happens while operation of vehicle. Traveling on the freeway at 55 mph. Abs malfunctions as well even when driving 15 mph. *Tr

Filed Incident Suspension · Electrical system · EngineNHTSA 10943875
Transmission & drivetrainCrash

My 1996 cirrus with only 87+++ miles suddenly downshifts while driving over 40 mph. This is a recent purchase. I live in wyoming and it is winter time with icy road conditions nearly everywhere. I am a single mother with a 10 year old daughter. When this happened to us on the highway, it caused us to spin off of the road. Luckily we were unhurt. This automobile is unsafe!!! The limp mode appears to be activated due to faulty/low quality parts by chrysler. Why isn"t this recalled??? I have no choice but to drive this car. I will sue chrysler if we have another incident!!! This incident occured when we were driving straight at about 50 mph.

Filed Incident Power trainNHTSA 10821703
Engine & coolingFire

Tl* the contact owns a 1996 chrysler cirrus. The contact stated that while the vehicle was parked, there was smoke seen from the engine compartment. The contact also noticed that there was oil leaking onto the ground. The fire was extinguished using a fire extinguisher. The dealer was contacted and they advised the contact that the vehicle was not included in nhtsa campaign id number: 96v006000 (engine and engine cooling:engine:gasoline). The vehicle was neither diagnosed nor repaired. The failure and the current mileage was 49,063.

Filed Incident Engine and engine coolingNHTSA 10452239
Suspension

Tl* the contact owns a 1996 chrysler cirrus. The contact stated that the rear lateral link fractured, causing the rear driver side tire to fold inward while driving 10 mph. The contact did not take the vehicle to the dealer or local mechanic for repairs or diagnostics. The failure mileage was 118,000.

Filed Incident SuspensionNHTSA 10438730
SuspensionAirbagsSeats & seat beltsCrash1 injury

Tl* the contact owns a 1996 chrysler cirrus. The contact stated that the driver was traveling 42 mph when the steering wheel became excessively loose. This made it difficult for the driver to maintain control of the vehicle. The vehicle independently veered off the road, and crashed into a electric pole, yet the vehicle did not stop. She then crashed into a second pole, jumped a creek and crashed into a tree as the vehicle came to a stop. The air bags did not deploy. The seat belts did not restrain the driver as...

Read the full complaint

she plunged into the steering wheel. She then exited the vehicle through the driver side window. The driver sustained injuries to the neck, shoulder, chest and a minor concussion. She also suffered short-term memory loss as a result. A police report was available. The manufacturer was contacted and advised that the vehicle was previously repaired under nhtsa campaign id number: 97v201000 (suspension: front: control arm: lower ball joint) which could potentially cause a loss of steering control. The contact was unaware that the vehicle was ever repaired in regards to the recall. The vehicle was destroyed. The failure and current mileage was approximately 180,000.

Filed Incident Suspension · Air bags · Seat beltsNHTSA 10355793
Suspension

Tl*the contact owns a 1996 chrysler cirrus. While driving approximately 25 to 30 mph on normal road conditions; the front driver side tire disengaged from the vehicle. The contact was able to safely drive into the emergency lane. Roadside assistance towed the vehicle to the residence. An authorized dealer and manufacturer were notified of the failure. Nhtsa campaign id number 09e056000 (suspension; front control arm: lower ball joint) is related to the failure. The vin was included in the recall defect; however,...

Read the full complaint

the dealer refused to repair the vehicle per the recall remedy. The vehicle is inoperable and has been not repaired. The contact had concerns of the safety risk involved. The failure and current mileages were 100,000.

Filed Incident SuspensionNHTSA 10289165
Suspension

The car started making a creaking sound in like the axles and then it became a grinding sound . We were driving down the road and the tire just came off we slid like 20 feet before coming to a stop. *Tr

Filed Incident SuspensionNHTSA 10258858
Fuel systemTransmission & drivetrainElectrical systemBody, doors & structureEquipment & accessories

Http://nhthqnwws111.Odi.Nhtsa.Dot.Gov/acms/docservlet/artemis/public/recalls/1998/v/rc-98v183-nn.Pdf recall has not been repaired and they have actually made it worse! *Tr

Filed Incident Fuel system, gasoline · Power train · Electrical system · Latches / locks / linkages · EquipmentNHTSA 10239936
Suspension

Tl*the contact owns a 1996 chrysler cirrus. While driving 30 mph, the driver's side lower tie rod dropped from the vehicle and the tire turned at a ninety degree angle. The contact left the vehicle to get a tow and, when he returned, the police removed the vehicle. Chrysler stated that the vehicle had previously been repaired according to nhtsa campaign id number 97v201000 (control arm: ball joint separation). The current and failure mileages were 80,000. Update 09/10/08 *cw updated 09/16/08*jb

Filed Incident SuspensionNHTSA 10235729
Engine & cooling

OIL IN MY RADIATOR. SLUDGE INSIDE OF MY ENGINE. *TR

Filed Incident Engine and engine coolingNHTSA 10232602
Engine & cooling

Tl*the contact owns a 1996 chrysler cirrus. While making a left turn between 10-20 mph, the vehicle lost power. The failure occurred on five different occasions and was repaired each time for a total cost of $2,283.04. The dealer stated that there were no recalls listed. The contact spoke with daimler chrysler on three occasions and they stated that nothing could be done. They stated that they do not own their dealerships and it would be the dealer's decision to make the repair or issue a recall. Daimler...

Read the full complaint

chrysler further stated that they would try and send a technician to inspect the vehicle; however, no one has yet to arrive. The failure occurs while driving, stopped, or making a right or left turn. The failure mileage was 49,784 and current mileage was 50,261.

Filed Incident Engine and engine coolingNHTSA 10214499
Fuel systemTransmission & drivetrainBody, doors & structure

Dt*: the contact stated there were three recalls were performed on the vehicle, which were not performed correctly. The fuel pump recall #06e091000, hood attachments #97v095000, and the ignition switch #98v183000 were the 3 recalls. All 3 recalls were completed but the problems were not corrected, and the service dealer and manufacturer were not willing to correct these issues further under the recall.

Filed Incident Fuel system, gasoline · Power train · StructureNHTSA 10174803
Transmission & drivetrain

Dt*: the contact stated the shifter could be taken out of gear without the key in the ignition and the check engine light illuminated. A nhtsa recall, #98v183000 was performed on the vehicle concerning, the park/neutral start switch however, the recall did not remedy the problem. The dealership would not offer a second repair under the recall.

Filed Incident Power trainNHTSA 10174575
Engine & cooling

Consumer's 1969 chrysler cirrus did not pass inspection due to a so called recall on the vehicle regarding the emission system. *Mr the consumer was told that there was no recall. The oil was thick and dirty at the bottom of the groove on the dip stick. The consumer requested to be compensated and or reimbursed for the time lost from work. *Sc *jb

Filed Incident Engine and engine cooling · Unknown or otherNHTSA 10125838
Wheels & tires

1996 Chrysler cirrus has problems with michelin tires p195/65x15.*Mr two of the vehicle's tires blewout within an hour of each other. The last blowout caused damage to the front lights. *Nm

Filed Incident TiresNHTSA 10117311
Brakes

After having the front brake pads replaced emergency brake locked and melted the brake drum without being engaged. While driving a passing motorist noticed fire coming from the rear of the vehicle and notified the consumer. Emergency braking system and drums had to be replaced. The cause of the failure was undetermined. *Ak

Filed Incident Service brakes, hydraulic · Parking brakeNHTSA 10094463
Engine & coolingVisibility & wipers

While crossing an intersection the consumer's vehicle stalled right in the middle of the intersection. After a few tries the vehicle was restarted. After driving a few feet the vehicle stalled once again. Also the windshield wipers work intermittently when it rained. When the wipers were on intermittent they would move very fast for that speed. *Jb

Filed Incident Engine and engine cooling · VisibilityNHTSA 10073837
Electrical system

When the vehicle is running and the doors are closed, the vehicle doors locks itself. *Ph on two occasions this problem occurred in which the consumer's child had gotten stuck in the vehicle after shutting the door to walk to the driver door the vehicle would lock itself. (Model/talon) *sc

Filed Electrical systemNHTSA 10065111
Visibility & wipers

Leaking evaporator. Strong refridgerant odor coming from hvac housing. (Inside vehicle) . *Ak

Filed Incident VisibilityNHTSA 10059999
Brakes

Loss of abs when applying brakes. This happens at all levels of braking, i.E. Heavy, medium and minimal braking. When loss of abs happens, the pedal decends to the floor and a buzz/racheting noise is heard. This problem has lead to potentially 4 major accidents. To solve the loss of braking, driver has to "re-pump" the pedal after loss has occured. (No mil/scan tool code recorded) . *Ak

Filed Incident Service brakes, hydraulicNHTSA 10059998
Engine & cooling

I bougt a car about 3 weeks ago used and have had several problems with the car already. From the engine light coming on to the battery light. The 3rd day I had the car it dhad to go in the shop. I feel the problem it had it was their when I bought it. I did not have thew car long enough for it to have problems. The car is a 96 chrsyler cirrus . *Ak

Filed Incident Engine and engine coolingNHTSA 10051572
Transmission & drivetrain

While traveling on the highway and without prior warning there was a explosion due to the trans axle loosening and busting the transmission case. *Ak the vehicle experienced loss of power steering and brakes. The transmission was serviced. *Ph *jb *jb *ph *jb

Filed Incident Power trainNHTSA 10032324
SteeringCrash

Passenger side rear wheel "knuckle" broke off where support arm to vehicle attaches. This causes rear wheel assembly to loose structural support. Rear wheel is then free to twist in all directions causing loss of control of the vehicle. At highway speeds this can cause a catastrophic accident. The "knuckle" is cast aluminum and has no moving parts which can wear out.*Ak

Filed Incident SteeringNHTSA 10037217
Seats & seat belts

While driving the drivers seat back collapsed. *Nlm

Filed Incident SeatsNHTSA 10023509
Electrical system

1/16/03 , Car would not start was cranked about 5 minutes later 1/2/037:00 pm car cut off while driving 7:30 pm went back at 8:15 pm and it cranked right up and drove home 3/5/03 van would not crank. After about 5 minutes of trying it cranked 7:30 a.M. And 48 degrees. Left home van cut out in the middle of the road, I got to the side of the road and again tried for about 5 minutes to crank it,10 min. Later it cut out again motor just cut off without warning got to dealer they said it had been reset and there...

Read the full complaint

where no codes 3/6/03 van shut off on (wet and rainy today) 3/7/03 van would not crank this morning. I tried for 30 minutes before it finally cranked 7:30 a.M. 3/14/03 Would not crank tried for 10 minutes then it cranked 7:30 3/15/03 van acted like it was going to cut off. Car hesitated about 3 times in 5 minutes. All the gauges dropped immediately to zero!!! Car kept running the first three times this happened finally it cut off. 5 Min. Later cranked up. 4/7 Van would not start. 5 Min. Later drove to work with no other problems. 4/8 Leaving work the van cut off, waited for about 5 minutes, then the van cranked. This is what I have been dealing with since the purchase of the car. I cannot drive it because I have small children and I think that cars that shut off at 65 miles an hour on the interstate need to be investigated!Even if you can't identify the problem you need to encourage the manufacturer to find the problem!In a letter from nhtsa sent to my state rep cass ballenger it was stated that there where numerous complaints "alleging" stalling like this but that no investigation was being done since it was of undetermined cause!! I need help now!!!Anyone that has an idea what is wrong please e-mail me [email protected]. *Nlm

Filed Incident Electrical systemNHTSA 10018726

Chrysler Cirrus: every year compared

YearComplaintsRecallsCrashesFiresTop problemGrade
200010791825SteeringD
199972762Transmission & drivetrainC
199876743Engine & coolingC
199776897BrakesC
199617411105Engine & coolingD
199538211465BrakesF
19943000Acceleration & cruise controlA
All Cirrus years

1996 Chrysler Cirrus vs rivals

More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.

Own a 1996 Chrysler Cirrus? Share your experience.

Your experience goes live straight away and helps every owner and buyer who checks this vehicle. Anonymous, free, no account.

Overall, how would you rate it? *

0/4000 · Please leave out names, phone numbers and your full VIN.

By posting you confirm it's your own, honest experience and agree to the rules. Safety defect? Also report it to NHTSA - that's how recalls start.

Questions about the 1996 Chrysler Cirrus

Does the 1996 Chrysler Cirrus have any recalls?

Yes - NHTSA lists 11 recalls for the 1996 Chrysler Cirrus: lower arm (December 2010); lower ball joint (October 2009); fuel pump (November 2006); fuel pump (October 2006) and more. Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.

What are the most common problems with the 1996 Chrysler Cirrus?

By the complaints owners filed with NHTSA, the most common problem areas are the engine & cooling (41), brakes (25), transmission & drivetrain (23).

How many complaints has the 1996 Chrysler Cirrus had?

174 complaints have been filed with NHTSA, the first on October 20, 1995 and the latest on January 9, 2017. Of these, 10 describe a crash and 5 a fire, and together they report 11 injuries and 0 deaths.

Is the 1996 Chrysler Cirrus a reliable vehicle?

Its Safety Index is 27 out of 100 (grade D: more problems than a typical Chrysler Cirrus year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.

Which Chrysler Cirrus years have the most complaints?
What should I do if my 1996 Chrysler Cirrus has a problem?

If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.

Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data

Owners helping owners

Know before you drive.

Every experience you share - good or bad - shows on that vehicle's page and helps the next owner and buyer. Two minutes, anonymous.

Share your experience