Check a vehicle VIN check Latest recalls Latest complaints Common problems Rankings Compare vehicles Recall roundups All makes Guides Share your experience
Theme

Vehicle safety record

2011 Mazda MAZDA6 Problems, complaints & recalls

Owners have filed 136 complaints about the 2011 Mazda MAZDA6 with NHTSA, most often about the suspension (51) and the body, doors & structure (30). Those complaints describe 8 crashes, 1 fire and 6 injuries. It is covered by 6 recalls, the latest in October 2019 for the inflator module. For comparison, the 2010 has 225 and the 2012 has 100.

NHTSA data checked

CAbout as many problems as a typical MAZDA6 year, for its age

#82 most complained-about 2011 vehicle

Complaints
136
Recalls
6
Crashes
8
Fires
1
Injuries
6
Deaths
0

Most common 2011 Mazda MAZDA6 problems

Share of all 136 complaints. One complaint can name more than one area. Tap an area for its complaints and recalls.

2011 Mazda MAZDA6 recalls 6

Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do

Air bags: inflator module

19V78200069,879 vehicles affected

Do not drive
The problem
Mazda North American Operations (Mazda) is recalling certain 2007-2012 CX-7, CX-9, and 2009-2012 Maza6 vehicles. These vehicles had their passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
The risk
An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
The fix
Owners are advised not to drive their vehicles until the repair has been performed. Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. The recall began December 3, 2019. Owners may contact Mazda customer service at 1-800-222-5500, option 4. Mazda's number for this recall is 1317F. Note: This recall supersedes recalls 16V356 and 17V012.

Structure

19V32300051,118 vehicles affected

The problem
Mazda North American Operations (Mazda) is recalling certain 2011-2013 Mazda6 vehicles sold, or ever registered in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland,Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. The front cross member may corrode after exposure to road salt.
The risk
Corrosion may weaken the mounting point for the passenger side lower control arm, unexpectedly changing the steering alignment and increasing the risk of a crash.
The fix
Mazda will notify owners, and dealers will inspect the cross member and either install a side member and drain hose and apply wax to protect from rust, or install a drain hose and an improved front cross member, free of charge. The recall began June 13, 2019. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 2818I. Note: This recall is an expansion of Recall 18V-631.

Air bags: inflator module

18V717000155,436 vehicles affected

Do not drive
The problem
Mazda North American Operations (Mazda) is recalling certain 2014-2015 Mazda CX-9 vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, unless covered in "Zone A," Mazda is recalling certain 2011-2013 Mazda6, 2011-2012 CX-7, and 2011-2015 CX-9 sold, or ever registered in the states of Arizona, Arkansas, Delaware, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, West Virginia and the District of Columbia, or "Zone B." Additionally, unless covered in Zone A or Zone B, Mazda is recalling certain 2010-2013 Mazda6, 2010-2012 CX-7, and 2010-2015 CX-9 vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
The risk
An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
The fix
Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate inflator, free of charge. The recall began November 9, 2018. Owners may contact Mazda customer service at 1-800-222-5500, Option 4. Mazda's number for this recall is 1317F.

Air bags: inflator module

17V429000205,377 vehicles affected

Do not drive
The problem
Mazda North America Operations (Mazda) is recalling certain 2009-2011 Mazda6, and 2007-2011 CX-7 and CX-9 vehicles. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
The risk
An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
The fix
Owners are advised not to drive their vehicles until the remedy is performed. Mazda will notify owners, and dealers will replace the passenger frontal air bag inflator with an alternate inflator, free of charge. The recall began on August 30, 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1317F. Note: This recall supersedes recall 16V356 and all vehicles that were not remedied under that campaign are now covered by this one.

Fuel system

14V11400042,000 vehicles affected

The problem
Mazda North America Operations (Mazda) is recalling certain model year 2010-2012 Mazda6 vehicles manufactured September 14, 2009, through May 2, 2011, and equipped with 2.5L engine. In the affected vehicles, spiders may weave a web in the evaporative canister vent hose, blocking it and causing the fuel tank to have an excessive amount of negative pressure.
The risk
Negative pressure could cause the fuel tank to crack resulting in a fuel leak, increasing the risk of a fire.
The fix
Mazda will notify owners, and dealers will reprogram the powertrain control module and inspect and clean the canister vent line. If a web was found in the line, the fuel tank and check valve on canister vent line will be replaced. These repairs will be done free of charge. The recall began on April 30, 2014. Owners may contact Mazda at 1-800-222-5500. Mazda's recall number associated with this campaign is 7214C.

Latch

13V425000161,400 vehicles affected

The problem
Mazda is recalling certain model year 2009-2013 Mazda6 vehicles manufactured February 4, 2008, through August 24, 2012. The door latch mounting screws may become loose.
The risk
If all three door latch mounting screws become excessively loose the door latch mechanism would not engage and the door might open while the vehicle is in motion increasing the risk of accident or injury.
The fix
Mazda will notify owners, and dealers will apply a thread locking adhesive to the door screws and retorque them, free of charge. The recall began on October 29, 2013. Owners may contact Mazda at 1-800-222-5500. Mazda's recall number is 7013I.

What owners say

Be the first MAZDA6 owner to share.

Problems or none - your experience is exactly what the next buyer is looking for. Write it now

136 complaints about the 2011 Mazda MAZDA6

Newest first, as filed with NHTSA by owners. Page 1 of 6.

SteeringSuspension

The frame rusted through and broke where the lower control arm attaches on the passenger side. This caused an immediate pull to the right and nearly caused a wreck. The car was towed to a local mechanic shop who reported the problem. Mazda is currently not taking responsibility for this even though it was a known issue and a recall was issued for this exact issue.

Filed Incident Steering · SuspensionNHTSA 11775340
SteeringSuspensionWheels & tires

Crossmember is rusted out and car is undriveable. There is a recall on the crossmember front subframe

Filed Incident Steering · Suspension · WheelsNHTSA 11765687
Body, doors & structure

The contact owns a 2011 Mazda Mazda6. The contact stated that while driving at an undisclosed speed and coming to a stop, the steering wheel was not operating properly. Several days later while the contact's wife was driving at an undisclosed speed, there was play in the steering wheel. Additionally, there was an abnormal sound coming from the passenger's side wheel. The contact stated that the wheel was turning abnormally. A mechanic arrived at the residence to diagnose the vehicle and determined that the sub...

Read the full complaint

frame was rusted. While touching the sub frame, pieces of the sub frame fractured. The dealer was notified of the failure. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 92,000.

Filed Incident StructureNHTSA 11744830
SuspensionBody, doors & structure

The contact owns a 2011 Mazda Mazda6. The contact stated that while driving at 25 MPH, the contact attempted to swerve out the way of another vehicle as she suddenly lost control of the vehicle. Due to the failure, the contact force to steer the vehicle to the left as the contact attempted to maintain control of the vehicle. The contact managed to pull over into a parking lot and called her husband for assistance. Despite the failure, the contact managed to drive the vehicle home despite the vehicle being...

Read the full complaint

extremely difficult to maneuver. The contact's husband managed to drive the vehicle to a local mechanic, who determined that the front subframe had failed due to excessive corrosion of the subframe. The mechanic then informed the contact of NHTSA Campaign Number: 19V323000 (Structure, Suspension); however, the contact was informed that her vehicle was not included in the recall. The manufacturer was notified of the failure where they confirmed that the vehicle was not included in the recall. The vehicle remained in the mechanic's possession and had yet to be repaired. The failure mileage was 115,000.

Filed Incident Suspension · StructureNHTSA 11738066
Body, doors & structure

Front Subframe has corroded and broke. There is a recall on the subframe that was repaired by dealership in 2019, but this repair did not fix the issue since it has now rusted through and broke. The repair was faulty.

Filed Incident StructureNHTSA 11730786
Body, doors & structureWheels & tires

Car developed a known recall issue problem, Recall 2818I. Even though Nebraska was not listed as a "salt state", it's obvious that Nebraska has similar conditions to Iowa. Attempts to contact Mazda USA corporate would not even fix the issue, citing cars age and other factors even though the damage is very specific to this particular recall.

Filed Incident Structure · Wheels · Unknown or otherNHTSA 11722303
SteeringSuspensionBody, doors & structure

2011 Mazda6 A serious safety defect occurred on my vehicle and matches NHTSA Recall 19V-323 / Mazda Recall 2818I (front cross member corrosion due to insufficient coating) despite this recall not being associated with my VIN. Front cross member cracked due to rust, causing loss of steering control, wheel misalignment, and scraping from the front wheel. This is exactly the failure described in the recall (breakage of the cross member and reduced steering control, increasing the risk of a crash). My safety and the...

Read the full complaint

safety of others were put at risk. Although my VIN is not currently associated with the recall, all conditions of the recall apply to my vehicle: -2011 Mazda6 within the affected production range -Defect is a manufacturing issue (insufficient paint coating) -Vehicle was registered in Missouri from 2023-2025, which is a listed state The only reason this recall was not associated with my VIN is because the vehicle was not registered in Missouri at the exact time of the 2019 recall campaign. This is an administrative gap, not a safety distinction. It should not be allowed to limit a manufacturer safety defect to specific states. Vehicles move across state lines constantly. A defect that causes loss of steering control does not stop being dangerous when a car crosses a border. Registration records alone did not reflect actual vehicle use or risk. If recalls are state-limited, manufacturers and NHTSA must continue tracking registration changes and associate the recall with the VIN as soon as a vehicle becomes registered in an affected state. Rust is progressive and age-related. Since this recall began in 2019 and it is now 2026, affected vehicles are more likely to experience failure, and many are now registered in different states than they were in 2019. I am requesting that NHTSA associate Recall 19V-323 with my VIN, investigate the adequacy of state-limited recall tracking, and take action to prevent this known safety defect from causing additional crashes.

Filed Incident Steering · Suspension · StructureNHTSA 11713263
Suspension

When I took the car into my ASE mechanic shop for a normal oil change and tire rotation, they performed a general overall car inspection. They noticed that the Driver Side Rear Subframe had rusted through completely, where the coil spring is located. The passenger side was rusted, but has not yet broke through. They stated that the subframe parts should not rust through like this. They also stated that it is dangerous to drive the car in this condition. I have not notified the manufacturer as of yet, but plan to do...

Read the full complaint

so. There were no warning lights, but the ride did seem to be rougher than normal. The attach photos contain 2 photos of the failed driver side rear subframe and 1 photo of the good, passenger side rear subframe.

Filed Incident Suspension · Unknown or otherNHTSA 11700788
Suspension

2011 Mazda6 rear subframe rot/rust, unsafe and dangerous to drive, Same situation as the front subframe that is part of a recall.

Filed Incident SuspensionNHTSA 11695663
SuspensionBody, doors & structure

The front and back cross members underneath my Mazda6 have completely rusted out. There are numerous complaints about Mazda's "Safety Recall 2818I Expansion" not covering the back support member and also not considering Nebraska to be a Salt Belt state despite the state, and specifically Omaha using salt to treat their roads in the winter. On [[redacted]], my front cross member completely failed due to rust, causing my vehicle to lose control. I've taken my car to the mechanic and they confirmed the front and back cross members are completely rusted and need replacement costing $7,000. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Filed Incident Suspension · StructureNHTSA 11682499
SuspensionBody, doors & structure

The contact owns a 2011 Mazda Mazda6. The contact stated that while her mother was driving at slow speeds in a parking area, there was an abnormally loud metallic sound coming from underneath the vehicle, and moments later, the vehicle became extremely difficult to maneuver. No warning lights were illuminated. The vehicle was towed to the dealer, who determined that the rear crossmember had detached from the vehicle due to excessive corrosion of the subframe. The contact was informed that the vehicle could not be...

Read the full complaint

repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 19V323000 (Structure, Suspension); the VIN was previously included, but was repaired in 2019. The contact stated that the recall repair was for the front passenger's side lower control arm. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 150,000.

Filed Incident Suspension · StructureNHTSA 11681707
Steering

Alignment is off. Recall for my type of call for the control arm weakening and causing wheel alignment problems. Why isn't mine part of recall??

Filed Incident SteeringNHTSA 11666615
Suspension

Front and rear subframe rust leading to gaping holes, outside of normal wear and tear.

Filed Incident SuspensionNHTSA 11649538
SuspensionBody, doors & structure

The contact owns a 2011 Mazda Mazda6. The contact stated that while the vehicle was at the dealer for routine service, the vehicle was diagnosed with rust and corrosion of the sub-frame. The contact was informed that the sub-frame needed to be replaced. The vehicle was not repaired. The contact was informed of NHTSA Campaign Number: 19V323000 (Structure, Suspension); however, the VIN was not included in the recall. The manufacturer was made aware of the failure. The contact was advised to contact the NTSA Hotline to report the failure. The failure mileage was approximately 100,000.

Filed Incident Suspension · StructureNHTSA 11627207
Suspension

The contact owns a 2011 Mazda Mazda6. The contact stated that while reversing, the contact heard an abnormal snapping sound coming from the rear passenger's side of the vehicle. The vehicle was stopped and inspected, where the contact observed a big spring pushing a bar into the ground on the rear passenger's side. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The failure mileage was approximately 184,000.

Filed Incident SuspensionNHTSA 11617312
Suspension

The rear cross member / AKA (Rear Subframe) P/N GEG1-28-80X has completely rusted out. The car is no longer safe to drive per a Pennsylvania State inspection. If driven parts of the rear suspension will drop off the car creating a hazard to other motorists and the driver of the car can lose control / mobility causing a traffic accident. Picture the entire rear suspension suddenly collapsing, that is what is going to happen. The Front subframe was subject to a recall. That recall should have included the rear...

Read the full complaint

as it is the same material just a few feet away, subject to the same rusting issues. These subframes were not property designed to prevent rust or even withstand a little moisture, as my car has been very well maintained. When I read the online forms this is a flaw in ALL 2009- 2013 Mazda 6's and the sister car the Ford Fusion and Mercury Milan. I have opened a case with Mazda USA case #[[redacted]]. They are going to inspect to confirm my mechanic diagnosis. However they are currently under no obligation to repair and replace the rusted parts but they should be as this should have been replaced when the front subframe recall was performed. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Filed Incident SuspensionNHTSA 11608007
SuspensionBody, doors & structure

After getting the recall information about the front crossmember rusting out due to corrosion, I decided to check the rear crossmember on my car. WOW, the rear crossmember is SO much worse than the front one and I've read hundreds of similar stories about the exact same thing happening to other Mazda 6 sedans around these model years (2009-2013). The rear crossmember on my car, which supports the entire rear suspension is completely rusted thru in several spots and the lower end links aren't even attached anymore...

Read the full complaint

because the brackets literally fell off and so now both back tires are leaning in at the top. It is very noticeable! Very unsafe to drive! I decided to park this car until a solution is reached with Mazda or the NHTSA on how to deal with this. I don't know why the front crossmember was recalled but not the rear? There's only 2 things that are rusted on my car, period...the front & rear crossmembers!

Filed Incident Suspension · StructureNHTSA 11605695
SuspensionBody, doors & structure

The contact owns a 2011 Mazda Mazda6. The contact stated that while the independent mechanic was performing an oil change on the vehicle, the independent mechanic informed the contact that the rear subframe was severely rusted with holes in the subframe. The vehicle was taken to the dealer, where it was determined that the rear subframe needed to be replaced. The vehicle was not repaired. The contact stated that the vehicle was previously repaired under NHTSA Campaign Number: 19V323000 (Structure, Suspension). The manufacturer was notified of the failure and informed the contact that the VIN was not included in the recall. The failure mileage was approximately 129,000.

Filed Incident Suspension · StructureNHTSA 11605184
Suspension

I'm filing a complaint as to substandard steel being used in the rear crossmember/rear subframe. Extensive corrosion has been confirmed upon a state inspection, which requires replacement at my personal cost. The front engine cradle was replaced in 2019, per a recall notice for the same extensive corrosion problem. A safety issue that needs to be addressed by Mazda.

Filed Incident SuspensionNHTSA 11603648
SteeringSuspension

Completely rusted rear crossmember subframe

Filed Incident Steering · SuspensionNHTSA 11595019
SuspensionBody, doors & structure

The contact's daughter owns a 2011 Mazda Mazda6. The contact stated that while her daughter was driving at an undisclosed speed, the steering wheel inadvertently moved to the left at a 30-35-degree angle. Additionally, the rear end of the vehicle swayed while coming to a stop. The vehicle was taken to an independent mechanic, who determined that the crossmember was severely corroded and the front driver's side crossmember had cracked. The vehicle was then towed to the dealer, where it was diagnosed that the front...

Read the full complaint

sub frame, sub frame link, sway bar, sub frame nuts, and bolts needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure and a case was opened. The contact related the failure to NHTSA Campaign Number: 19V323000 (Structure, Suspension); however, the VIN was not included in the recall. The failure mileage was approximately 89,000.

Filed Incident Suspension · StructureNHTSA 11587143
Suspension

Rear subframe rusted and cracked in half when my daughter was on a major highway!

Filed Incident SuspensionNHTSA 11580652
Suspension

My 2011 Mazda 6 rear suspension broke while my wife was driving our car on the highway. It could have killed my wife and son. The frame is rusted so bad that the lower control arm broke away from the frame, the rear wheel is barely hanging on it by one bolt on the front control arm. It is very much a safety issue and Mazda needs to take charge of the problem before someone dies in their vehicle. Our car has 106215 miles on it and we still owe alot of money on this thing.

Filed Incident SuspensionNHTSA 11577809
Steering

Bought. A 2011 Mazda 6, and took it to a Mazda dealer for an inspection. They found the rear sub frame ie rear cradle to be extremely rusted out, the shocks on both side are detached, and the springs look like they may push through at any point and do more damage. The car is unsafe to drive and the dealer estimated a repair cost or $4322.99 to fix.

Filed Incident Steering · Unknown or otherNHTSA 11570961
SuspensionBody, doors & structure

The rear cross member/subframe is completely rusted in two and the rear lower forward control arm is detached from cross member/subframe on both sides. There is currently an active recall for the front cross member due to accelerated corrosion from road salt but I'm not aware of any inclusion of the rear frame or suspension components tied in with this recall. It definitely needs added to it as this is VERY dangerous, possibly even more so than the front. Rest of the actual car body is fine, except for a little bit...

Read the full complaint

of surface rust. Please add this to the current corrosion recall! Car is registered in WV and is available for inspection anytime and I will be attaching pictures and I also have a video but it won't let me post it on here.

Filed Incident Suspension · StructureNHTSA 11570675

Mazda MAZDA6: every year compared

YearComplaintsRecallsCrashesFiresTop problemGrade
201560360BrakesB
20141374140Electrical systemC
201323410BrakesA
2012100652AirbagsC
2011136681SuspensionC
2010225952Body, doors & structureD
20093861083Body, doors & structureF
20081115152AirbagsC
20071656152AirbagsD
All MAZDA6 years

2011 Mazda MAZDA6 vs rivals

More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.

Own a 2011 Mazda MAZDA6? Share your experience.

Your experience goes live straight away and helps every owner and buyer who checks this vehicle. Anonymous, free, no account.

Overall, how would you rate it? *

0/4000 · Please leave out names, phone numbers and your full VIN.

By posting you confirm it's your own, honest experience and agree to the rules. Safety defect? Also report it to NHTSA - that's how recalls start.

Questions about the 2011 Mazda MAZDA6

Does the 2011 Mazda MAZDA6 have any recalls?

Yes - NHTSA lists 6 recalls for the 2011 Mazda MAZDA6: inflator module (October 2019); structure (April 2019); inflator module (October 2018); inflator module (June 2017) and more. Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.

What are the most common problems with the 2011 Mazda MAZDA6?

By the complaints owners filed with NHTSA, the most common problem areas are the suspension (51), body, doors & structure (30), airbags (28).

How many complaints has the 2011 Mazda MAZDA6 had?

136 complaints have been filed with NHTSA, the first on November 21, 2011 and the latest on November 3, 2026. Of these, 8 describe a crash and 1 a fire, and together they report 6 injuries and 0 deaths.

Is the 2011 Mazda MAZDA6 a reliable vehicle?

Its Safety Index is 45 out of 100 (grade C: about as many problems as a typical Mazda MAZDA6 year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.

Which Mazda MAZDA6 years have the most complaints?
What should I do if my 2011 Mazda MAZDA6 has a problem?

If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.

Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data

Owners helping owners

Know before you drive.

Every experience you share - good or bad - shows on that vehicle's page and helps the next owner and buyer. Two minutes, anonymous.

Share your experience