Check a vehicle VIN check Latest recalls Latest complaints Common problems Rankings Compare vehicles Recall roundups All makes Guides Share your experience
Theme

Vehicle safety record

2012 Mazda MAZDA6 Problems, complaints & recalls

Owners have filed 100 complaints about the 2012 Mazda MAZDA6 with NHTSA, most often about the airbags (30) and the lights (28). Those complaints describe 5 crashes, 2 fires and 6 injuries. It is covered by 6 recalls, the latest in October 2019 for the inflator module. For comparison, the 2011 has 136 and the 2013 has 23.

NHTSA data checked

CAbout as many problems as a typical MAZDA6 year, for its age

#93 most complained-about 2012 vehicle

Complaints
100
Recalls
6
Crashes
5
Fires
2
Injuries
6
Deaths
0

Most common 2012 Mazda MAZDA6 problems

Share of all 100 complaints. One complaint can name more than one area. Tap an area for its complaints and recalls.

2012 Mazda MAZDA6 recalls 6

Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do

Air bags: inflator module

19V78200069,879 vehicles affected

Do not drive
The problem
Mazda North American Operations (Mazda) is recalling certain 2007-2012 CX-7, CX-9, and 2009-2012 Maza6 vehicles. These vehicles had their passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
The risk
An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
The fix
Owners are advised not to drive their vehicles until the repair has been performed. Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. The recall began December 3, 2019. Owners may contact Mazda customer service at 1-800-222-5500, option 4. Mazda's number for this recall is 1317F. Note: This recall supersedes recalls 16V356 and 17V012.

Structure

19V32300051,118 vehicles affected

The problem
Mazda North American Operations (Mazda) is recalling certain 2011-2013 Mazda6 vehicles sold, or ever registered in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland,Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. The front cross member may corrode after exposure to road salt.
The risk
Corrosion may weaken the mounting point for the passenger side lower control arm, unexpectedly changing the steering alignment and increasing the risk of a crash.
The fix
Mazda will notify owners, and dealers will inspect the cross member and either install a side member and drain hose and apply wax to protect from rust, or install a drain hose and an improved front cross member, free of charge. The recall began June 13, 2019. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 2818I. Note: This recall is an expansion of Recall 18V-631.

Air bags: inflator module

18V717000155,436 vehicles affected

Do not drive
The problem
Mazda North American Operations (Mazda) is recalling certain 2014-2015 Mazda CX-9 vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, unless covered in "Zone A," Mazda is recalling certain 2011-2013 Mazda6, 2011-2012 CX-7, and 2011-2015 CX-9 sold, or ever registered in the states of Arizona, Arkansas, Delaware, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, West Virginia and the District of Columbia, or "Zone B." Additionally, unless covered in Zone A or Zone B, Mazda is recalling certain 2010-2013 Mazda6, 2010-2012 CX-7, and 2010-2015 CX-9 vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
The risk
An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
The fix
Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate inflator, free of charge. The recall began November 9, 2018. Owners may contact Mazda customer service at 1-800-222-5500, Option 4. Mazda's number for this recall is 1317F.

Air bags: inflator module

17V45700079,402 vehicles affected

Do not drive
The problem
Mazda North America Operations (Mazda) is recalling certain 2012 CX-7, CX-9 and Mazda6 vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Mazda is recalling certain 2009 CX-7, CX-9 and Mazda6 vehicles sold, or ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Additionally, unless included in "Zone A" or "Zone B" above, Mazda is recalling certain 2007-2008 CX-7 and CX-9 sold, or ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
The risk
An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
The fix
Owners are advised not to drive their vehicles until the remedy is performed. Mazda will notify owners, and dealers will replace the front passenger side air bag inflator with an alternate inflator, free of charge. The recall began October 4, 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1317F. Note: This recall supersedes recall 17V-012.

Fuel system

14V11400042,000 vehicles affected

The problem
Mazda North America Operations (Mazda) is recalling certain model year 2010-2012 Mazda6 vehicles manufactured September 14, 2009, through May 2, 2011, and equipped with 2.5L engine. In the affected vehicles, spiders may weave a web in the evaporative canister vent hose, blocking it and causing the fuel tank to have an excessive amount of negative pressure.
The risk
Negative pressure could cause the fuel tank to crack resulting in a fuel leak, increasing the risk of a fire.
The fix
Mazda will notify owners, and dealers will reprogram the powertrain control module and inspect and clean the canister vent line. If a web was found in the line, the fuel tank and check valve on canister vent line will be replaced. These repairs will be done free of charge. The recall began on April 30, 2014. Owners may contact Mazda at 1-800-222-5500. Mazda's recall number associated with this campaign is 7214C.

Latch

13V425000161,400 vehicles affected

The problem
Mazda is recalling certain model year 2009-2013 Mazda6 vehicles manufactured February 4, 2008, through August 24, 2012. The door latch mounting screws may become loose.
The risk
If all three door latch mounting screws become excessively loose the door latch mechanism would not engage and the door might open while the vehicle is in motion increasing the risk of accident or injury.
The fix
Mazda will notify owners, and dealers will apply a thread locking adhesive to the door screws and retorque them, free of charge. The recall began on October 29, 2013. Owners may contact Mazda at 1-800-222-5500. Mazda's recall number is 7013I.

What owners say

Be the first MAZDA6 owner to share.

Problems or none - your experience is exactly what the next buyer is looking for. Write it now

100 complaints about the 2012 Mazda MAZDA6

Newest first, as filed with NHTSA by owners. Page 1 of 4.

Suspension

i went to a mechanic to diagnose a clunk and rattle at freeway speeds. i was told a huge piece of metal was loose over a rotted out subframe. i told the mechanic there was a recall for a brace or bracket passenger side of the subframe. but no open recall was showing. he stated i hope this is not the piece a Mazda dealer would provide to fix that. he said it is loose and cannot be reattached and that i need to contact Mazda. he is stating i need a new subframe and the car should have never been sold to me in that condition. and to no longer drive it since it is going to split apart

Filed Incident SuspensionNHTSA 11774673
Other & unknown

Passenger dash has cracked some and dash is very very sticky..why has this happened..I feel if airbag had to deploy it would not because of this situation

Filed Incident Unknown or otherNHTSA 11711883
Suspension

The rear subframe and suspension parts are rusted so bad that the car is not safe to drive. Looked up recalls and found out the front subframe had a recall and was taken care of before I bought the car. Also found recall for my model of car that were registered in state that use salt on there roads which is one of the state i live in. Was told my Mazda corporation the only certain 2012 mazda vehicle's vehicle's were covered for rusting issues with the rear . If the front of the car is recalled and the same problem...

Read the full complaint

happens with the rear of the car shouldn't it be covered for something? I have an appointment coming up on the 21 of January which is ridiculous that I have to wait 3 weeks to have it looked at. . Thank you for your time. The only reason I found the problem with the car was a stick got stuck in the rusted out parts and when I took it out a bunch of rust fell on the ground.

Filed Incident Suspension · Unknown or otherNHTSA 11710529
SuspensionBody, doors & structure

The contact owns a 2012 Mazda Mazda6. The contact stated while driving 55 MPH and crossing a bridge, the vehicle stopped unexpectedly after driving over several expansion joints. The contact stated that the vehicle had not stalled. The contact exited the vehicle and noticed that the passenger's side front wheel was slanted into the wheel well. The contact inspected the wheel well and noticed that the control arm had sheared off at the cross member. The contact stated that prior to the failure, the steering wheel...

Read the full complaint

had turned slightly to the right. The contact researched online and related the failure to NHTSA Campaign Number: 19V323000 (Structure, Suspension), which included the VIN. The contact stated that the vehicle was towed to a dealer, where the contact was advised that the VIN was included in a recall, and the contact was advised that the vehicle needed to be diagnosed to determine the cause of the failure. The contact stated that the dealer had not diagnosed vehicle in a month. The manufacturer was informed of the failure and advised the contact to work with the dealer. The vehicle was not diagnosed or repaired. The contact stated that the manufacturer and dealer had exceeded a reasonable amount of time for the recall repair. The failure mileage was approximately 188,000.

Filed Incident Suspension · StructureNHTSA 11698215
SuspensionBody, doors & structure

The contact owns a 2012 Mazda Mazda6. The contact stated while driving 55 MPH, the steering wheel began to shake violently, with the low tire pressure warning light illuminated. The contact pulled over to inspect the vehicle and discovered that the front passenger's side tire had detached from the vehicle. The contact's father was called to the scene and the spare tire was placed on the vehicle. The contact then drove to an independent mechanic where both the front driver's and front passenger's side tires were...

Read the full complaint

replaced. The manufacturer was notified of the failure and referred the contact to the dealer for assistance. The vehicle was taken to the dealer where a diagnostic test was performed; and the diagnostic test determined that the cross member had corroded and caused the tire failure. The contact was then notified that the vehicle was not covered under NHTSA Campaign Number: 19V323000 (Structure, Suspension) and that the warranty on the vehicle had expired. The vehicle remained in the possession of the dealer and was not repaired. The failure mileage was 204,000.

Filed Incident Suspension · StructureNHTSA 11605371
Suspension

Front subframe completely rusted out causing loss of steering. I believe this should have been covered by Safety Recall 2818I which addresses the issue. Mazda inspected and said because the recall was performed in 2019 on this car, there is nothing more they can do, once and done. Unfortunately their fix didn't take care of the issue.

Filed Incident SuspensionNHTSA 11603117
Body, doors & structure

My 2012 mazda 6 Subframe is is unsafe to drive due to over-time corrosion My local mechanics said Madzda Corp. should fix it.

Filed Incident StructureNHTSA 11593397
Suspension

Rear sub frame, critical fail- rusted through. Needs new rear subframe. Wheel pulling to right, unable to align. I bought this car 2 weeks ago for my 16 year old daughter and was told today it needs to be scrapped. She is devastated . We are out 4500 with no recourse. I bought a Mazda because I trusted the safety. I am so disappointed. If the front was recalled the rear should have been too.

Filed Incident SuspensionNHTSA 11588995
Other & unknown

The rear subframe is rusted in layers and is spalling off.

Filed Incident Unknown or otherNHTSA 11575655
Airbags

The passenger dash board is melting. It covers the passengers air bag. I would like to know if a recall is still possible for my vehicle. I understand that there was a recall in 2015-2017, but unfortunately I did not received the notice since I was moving from Illinois to Kansas and later to Texas and continued changing addresses during that time frame.

Filed Incident Air bags · Unknown or otherNHTSA 11563908
Suspension

Severe rusting of the rear frame and suspension

Filed Incident SuspensionNHTSA 11562915
Steering

I was driving down the road when my steering, suddenly and with out warning began pulling very hard to the right and the steering wheel began turning to the left. My car made loud noises when I tried to straighten out the steering wheel and when I tried to turn. Its also appeared to be rubbing on the inside of the wheel well. Further inspection revealed that the support where the control arm is connected to the frame had torn away from the frame due to oxidation. There is significant oxidation on the frame and there are large areas that no longer appear to be solid.

Filed Incident Steering · Unknown or otherNHTSA 11518399
Body, doors & structure

The passenger side Dash on my 2012 Mazda 6 that I just purchased 3 years ago is melting and deteriorating and it's cracked and its leaves a real bad glare on the windshield and I think they said it was a recall that was back in 2015 but this car was never fixed and that recall wasn't fixed so how do I go about getting that recall fixed because when I talk to [[redacted]] at Mazda direct and Fostoria they said that there was nothing they could do and it is a real bad safety hazard. INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).

Filed Incident Unknown or other · StructureNHTSA 11517434
SteeringSuspension

I felt something was weird with the steering one day so I went to mazda dealer because I noticed corrosion on front driver cross and rear components which have corrosion and baseball size holes. Inspected by local mazda dealer in early 2022 was told "we see a lot worse than this" so nothing was fixed or replaced by dealer. October 2022 failed pa state inspection for subframe rust safety concerns. 2023 Got another mechanic to look and they estimate over $6,000 repair cost (docs. Attached). Serious safety concerns causes vehicle to sit unused which makes it available for inspection anytime. Police or insurance representative were not contacted but can be if needed.

Filed Incident Steering · Suspension · Unknown or otherNHTSA 11501876
Other & unknown

Sun/moonroof exploded. My own and others' safety were at risk due to falling broken glass The problem was not confirmed by a dealer yet The vehicle will be inspected from glass company/dealer No warning messages or lights indicated the failure.

Filed Incident Unknown or otherNHTSA 11466654
Body, doors & structure

Hello, I have 2012 Mazda6 was involved in a previous Safety Recall in regards to a rusting engine subframe. I was informed to bring my car in my local Mazda Dealer. My car has serious rusting issues with my subframe, Mazda decided in lieu of replacing the subframe they attached a subframe brace. While having my car serviced the mechanic and I noticed SEVERE rusting at the subframe which this recall was suppose to taken cared of. Ive attached a couple of pics but I have more that details the severe rusting. I feel a little disheartened that this recall fix the issue adequately. I want to 100% confident that the car is truely safe to drive for me and my family.

Filed Incident StructureNHTSA 11441655
Suspension

I was stopped at a red light in town and went to make a left hand turn when I heard a loud pop and then a springing noise. I myself looked under the car and just assumed I ran over something and it hit the bottom of the car. I had a friend look under it also and he didn't see anything either. I just found this out yesterday when it failed inspection.

Filed Incident SuspensionNHTSA 11342664
Electrical system

I own a 2012 mazda 6, vin#[[redacted]], that I bought in 2012. For the past couple of years I've been dealing with electrical issues with this car. For a few years I was just dealing with the headlights continuously going out every 3 or 4 months. At first I was thinking the light was defective, but after some research I learned that this is a more than a common occurrence with these cars. This is the main complaint. It has been linked to the electrical system that your service department said was the issue. It also...

Read the full complaint

mentioned the electrical issue causing the car to suddenly shut down which is the problem I am currently having now. My car has shutdown a total of 4 times, the last time being on the interstate. This is ridiculous! This is a known problem by mazda that has not been addressed. Are you waiting for someone to die in an accident? This needs to be fixed immediately. My daughter drives this car! Information redacted pursuant to the freedom of information act (foia), 5 u.S.C. 552(B)(6). *Tr

Filed Incident Electrical systemNHTSA 11326448
Lights

My low headlight beams continue to burn out, especially the driver side. They were last replaced less than 2 weeks ago and the driver side is out again. I did a google search and there were multiple complaints of this happening to other people. What's worse is that for the low beams it has to be taken to a mazda dealership to be replaced. It's a safety hazard and expensive!

Filed Incident Exterior lightingNHTSA 11317621
Airbags

There was a recall on the air bags of my car and I was not informed of the recall that was for april 2019. How can this be fixed?

Filed Incident Air bags · Unknown or otherNHTSA 11298899
Other & unknown

The passenger side of my mazda 6 2012 is literally melting. The dashboard is all sticky and has a glare that affects my ability to see out the window. The passenger dashboard is cracking and has pieces that are falling off. It is a hazard because it causes a glare that limits my ability to see.

Filed Incident Unknown or otherNHTSA 11290372
Lights

Headlight on driver side was burning out every other month needing replaced. Recently changed headlight and the bulb is fine but the adapter inside the assembly is burned and charred. Just went to change the passenger side and it has the same issue. Good bulb but the adapter to attach bulb is burned. Reading many complaints online about this being a common issue with 2012 mazda 6. Including issues of lights going out while people are driving and having to tap on the headlight to get it to turn on.

Filed Incident Exterior lightingNHTSA 11271225
Body, doors & structure

There was a recall on the door latches back in 2013 which I got repaired. Today 10/20/2019 after driving on highway 15 south dropping off my kids my son went to close the back passenger door that did not close I had to purchase rope and tape to hold it close so I could drive back home going on the 15 north highway. This is a huge safety issue I would like to have this issue fix asap I will call the dealer tomorrow and hope they can repair without me coming out of pocket

Filed Incident StructureNHTSA 11269788
Electrical system

BOTH HEADLIGHTS ON VEHICLE IS NOT WORKING

Filed Incident Electrical systemNHTSA 11266444
Electrical systemBody, doors & structure

Tl* the contact owns a 2012 mazda 6. While driving approximately 45 mph, the door open icon illuminated. The contact pulled over to the side of the road to check the doors; however, all the doors were closed. The vehicle was taken to hennessy mazda (7261 jonesboro rd, morrow, ga 30260) to be diagnosed, but they were not able to determine the cause of the failure. The manufacturer was not notified. The vehicle was not repaired. The approximate failure mileage was 96,000.

Filed Incident Electrical system · StructureNHTSA 11231888

Mazda MAZDA6: every year compared

YearComplaintsRecallsCrashesFiresTop problemGrade
201678190BrakesB
201560360BrakesB
20141374140Electrical systemC
201323410BrakesA
2012100652AirbagsC
2011136681SuspensionC
2010225952Body, doors & structureD
20093861083Body, doors & structureF
20081115152AirbagsC
All MAZDA6 years

2012 Mazda MAZDA6 vs rivals

More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.

Own a 2012 Mazda MAZDA6? Share your experience.

Your experience goes live straight away and helps every owner and buyer who checks this vehicle. Anonymous, free, no account.

Overall, how would you rate it? *

0/4000 · Please leave out names, phone numbers and your full VIN.

By posting you confirm it's your own, honest experience and agree to the rules. Safety defect? Also report it to NHTSA - that's how recalls start.

Questions about the 2012 Mazda MAZDA6

Does the 2012 Mazda MAZDA6 have any recalls?

Yes - NHTSA lists 6 recalls for the 2012 Mazda MAZDA6: inflator module (October 2019); structure (April 2019); inflator module (October 2018); inflator module (July 2017) and more. Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.

What are the most common problems with the 2012 Mazda MAZDA6?

By the complaints owners filed with NHTSA, the most common problem areas are the airbags (30), lights (28), body, doors & structure (12).

How many complaints has the 2012 Mazda MAZDA6 had?

100 complaints have been filed with NHTSA, the first on August 23, 2011 and the latest on October 30, 2026. Of these, 5 describe a crash and 2 a fire, and together they report 6 injuries and 0 deaths.

Is the 2012 Mazda MAZDA6 a reliable vehicle?

Its Safety Index is 54 out of 100 (grade C: about as many problems as a typical Mazda MAZDA6 year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.

Which Mazda MAZDA6 years have the most complaints?
What should I do if my 2012 Mazda MAZDA6 has a problem?

If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.

Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data

Owners helping owners

Know before you drive.

Every experience you share - good or bad - shows on that vehicle's page and helps the next owner and buyer. Two minutes, anonymous.

Share your experience