- The problem
- Chrysler (FCA US, LLC) is recalling certain 2016-2019 Ram 3500, Ram 1500, 2016-2020 Ram 2500, and 2016 Ram 3500 Cab Chassis vehicles. The right and left side curtain air bag inflators may rupture due to a manufacturing defect.
- The risk
- An inflator rupture may result in sharp metal fragments striking occupants, resulting in injury.
- The fix
- Dealers will replace one or both side curtain air bags, as necessary, free of charge. Owner notification letters were mailed February 13, 2025. Owners may contact FCA customer service at 1-800-853-1403. FCA's numbers for this recall are 05C, 09C, and 10C.
Vehicle safety record
2016 Ram 2500 Problems, complaints & recalls
Owners have filed 261 complaints about the 2016 Ram 2500 with NHTSA, most often about the transmission & drivetrain (64) and the engine & cooling (57). Those complaints describe 16 crashes, 3 fires, 10 injuries and 1 death. It is covered by 14 recalls, the latest in January 2025 for the inflator. For comparison, the 2015 has 215 and the 2017 has 699.
NHTSA data checked
CAbout as many problems as a typical 2500 year, for its age
#50 most complained-about 2016 vehicle
- Complaints
- 261
- Recalls
- 14
- Crashes
- 16
- Fires
- 3
- Injuries
- 10
- Deaths
- 1
Most common 2016 Ram 2500 problems
Share of all 261 complaints. One complaint can name more than one area. Tap an area for its complaints and recalls.
2016 Ram 2500 recalls 14
Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do
- The problem
- Chrysler (FCA US, LLC) is recalling certain 2015-2020 Ram 1500 Classic, 2015-2016 Ram 3500, and Ram 2500 vehicles, and 2016 Ram 3500 Cab Chassis with a gross vehicle weight rating less than 10,000 lbs. The side air bag inflatable curtain (SABIC) inflator end cap may detach from the inflator, or the inflator sidewall may rupture.
- The risk
- A separated inflator end cap or inflator rupture can allow compressed gas to escape, resulting in the end cap or other components being propelled into the vehicle, increasing the risk of injury or crash.
- The fix
- Dealers will inspect and replace as necessary, the SABIC assemblies, free of charge. Interim owner notification letters were mailed on October 4, 2021. Owner notification letters were mailed on May 26, 2022. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is Y55.
- The problem
- Chrysler (FCA US LLC) is recalling certain 2015-2017 Ram 1500, 2500 and 3500 pickup trucks equipped with an 8 foot bed and a power locking tailgate. Chrysler is also recalling all 2013-2014 and 2018 Ram 1500, 2500 and 3500 pickup trucks built before April 1, 2018 with a 6 or 8 foot bed and a power locking tailgate. On August 29, 2019 Chrysler expanded the recall to include an additional 693,128 model year 2013-2014 Ram 1500, 2500 and 3500 pickup trucks. The tailgate actuator limiter tab may fracture and cause the tailgate to unlatch and open while driving.
- The risk
- If the tailgate opens while the vehicle is being driven, cargo may fall out the vehicle and create a road hazard, increasing the risk of crash.
- The fix
- Chrysler will notify owners, and dealers will repair the tailgate latch, free of charge. The recall began May 23, 2019. Chrysler is expected to notify owners of the expanded population on October 18, 2019. Owners may contact FCA US customer service at 1-800-853-1403. FCA US's number for this recall is V44. Note: 2015-2017 MY Ram 1500 pickup trucks with truck beds other than 8 foot, are currently covered under NHTSA recall 18V-486 for this issue.
- The problem
- Chrysler (FCA US LLC) is recalling certain 2013-2018 Ram 3500 and 2014-2018 Ram 3500 Chassis Cab and Ram 2500 vehicles. The outboard steering linkage jam nut may loosen, allowing one end of the drag link to separate.
- The risk
- A drag link separation can cause a loss of steering control, increasing the risk of crash.
- The fix
- Chrysler will notify owners, and dealers will check the steering linkage jam nut tightness, replacing the drag link assembly or welding the nut to the adjuster sleeve, free of charge. The recall began March 22, 2019. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is V06.
- The problem
- Streetcar ORV LLC (Streetcar) is recalling certain American Expedition Vehicles (AEV) 3" Dualsport aftermarket suspension kits, part numbers N0436000 and N0436001, sold for installation on 2013-2018 RAM 2500 and 3500HD trucks. Improper installation and machining of the original equipment steering knuckle may weaken the joint between the steering drag link and knuckle.
- The risk
- The weakened connection may result in a fractured steering drag link, causing a loss of steering and increasing the risk of a crash.
- The fix
- Streetcar will notify owners and dealers will inspect and install a new steering knuckle, free of charge. The recall began December 3, 2018. Owners may contact AEV customer service at 1-248-926-0256, extension 500.
- The problem
- Chrysler (FCA US LLC) is recalling certain 2015-2017 RAM 1500, 2500, and 3500 pickup trucks equipped with a power locking tailgate and either a 5 foot, 7 inch or 6 foot, 4 inch bed. The tailgate actuator limiter tab may fracture and cause the tailgate to unlatch and open while driving.
- The risk
- If the tailgate latch releases and the tailgate opens while driving, cargo may fall out, creating a road hazard and increasing the risk of a crash.
- The fix
- Chrysler will notify owners, and dealers will repair the vehicle, free of charge. The recall began September 17, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U74.
- The problem
- Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
- The risk
- If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
- The fix
- Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
- The problem
- Chrysler (FCA US LLC) is recalling various Dodge, Chrysler, and RAM vehicles equipped with Kidde Plastic-Handle or Push Button 'Pindicator' Fire Extinguishers. A list of the affected trailer models is available at: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17V824-0103.pdf. These extinguishers may become clogged, preventing the extinguisher from discharging as expected or requiring excessive force to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf
- The risk
- If the fire extinguisher does not function properly, it can increase the risk of injury in the event of a fire.
- The fix
- Chrysler will notify owners instructing them to contact Kidde for a replacement fire extinguisher, free of charge. The recall began February 14, 2018. Owners may contact Chrysler customer service at 1-800-853-1403 or Kidde customer service service toll-free at 1-855-262-3540, or online at www.kidde.com and click on "Product Safety Recall" for more information. Chrysler's number for this recall is T82.
- The problem
- Chrysler (FCA US LLC) is recalling certain 2016-2017 Ram 3500 Cab Chassis with a Gross Vehicle Weight Rating (GVWR) of less than 10,000 lbs, 2011-2017 Ram 3500, 4500 and 5500 Cab Chassis vehicles, 2009-2017 Ram 1500 and 2010-2017 Ram 2500 and 3500 pickup trucks, all equipped with a column shifter. Pushing the brake pedal for prolonged periods when the vehicle is running and in PARK may cause the Brake Transmission Shift Interlock (BTSI) pin to stick in the open position. With the pin in the open position, the transmission can be shifted out of PARK into any gear without pushing the brake pedal or having the key in the ignition.
- The risk
- Being able to shift the transmission without pushing the brake pedal and/or without a key in the ignition can increase the risk of an unintended vehicle rollaway that may result in personal injury or a crash.
- The fix
- Chrysler will notify owners, and dealers will update the vehicle software, inspect the BTSI, and, as necessary, replace it, free of charge. The recall began February 26, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T79.
- The problem
- Chrysler (FCA US LLC) is recalling certain 2013-2017 RAM 2500, 3500, 3500 Cab Chassis, 4500 Cab Chassis, and 5500 Cab Chassis vehicles, equipped with Cummins 6.7L Turbo Diesel engines that have Concentric-brand water pumps without a vent hole. These water pumps may leak coolant.
- The risk
- The leaking water pump can increase the risk of an engine compartment fire.
- The fix
- Chrysler will notify owners, and dealers will replace the water pumps, free of charge. The recall began February 26, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T51.
- The problem
- Streetcar ORV LLC, dba American Expedition Vehicles (AEV) is recalling certain 2013-2017 RAM 2500 and 3500 heavy duty trucks, modified by AEV to be equipped with cast aluminum Katla 8.5" road wheels. The outer surface of the wheel may fracture, resulting in rapid air loss.
- The risk
- If the wheel fractures, a loss of vehicle control can occur, increasing the risk of a crash.
- The fix
- AEV will notify owners, and dealers will replace the wheels with wheels of similar value, free of charge. The recall began on August 30, 2017. Owners may contact AEV customer service at 1-248-926-0256 extension 500.
- The problem
- Chrysler (FCA US LLC) is recalling certain model year 2013-2016 Ram 1500, Ram 2500, and 2014-2016 Ram 3500 vehicles. Certain driving conditions, such as driving off-road or debris striking the vehicle may cause the roll rate sensor to trigger a fault within the Occupant Restraint Controller (ORC). If this fault occurs, the rollover side curtain air bag and the seat belt pretensioner will be disabled from deploying.
- The risk
- If the rollover side curtain air bags and seat belt pretensioners are disabled, there is an increased risk of injury to the vehicle occupants in the event of a crash that necessitates activation of these safety systems.
- The fix
- Chrysler will notify owners, and dealers will update the ORC software, free of charge. The recall began June 26, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T25.
- The problem
- Chrysler (FCA US LLC) is recalling aftermarket Mopar Canvas Seat Covers for certain 2012-2016 RAM 1500, 2500, and 3500 trucks. These Mopar canvas seat covers were sold through Chrysler dealerships beginning October 15, 2015. The seat covers can impede the deployment of the seat thorax airbags.
- The risk
- If the seat cover impedes the air bag deployment, the seat thorax air bags may not provide adequate protection in the event of a crash, increasing the risk of a injury.
- The fix
- Chrysler will notify owners to remove the front seat covers and return them for a full refund. The recall began on July 1, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S30.
- The problem
- Chrysler (FCA US LLC) is recalling certain model year 2016 Ram 2500, 3500, 3500 Cab Chassis and 4500/5500 Cab Chassis trucks manufactured July 31, 2015, to August 13, 2015 and equipped with a 6.7L Cummins Diesel engine. In the affected vehicles, the Engine Control Module (ECM) may short circuit, causing the engine to stall without warning.
- The risk
- An engine that stalls without warning increases the risk of a crash.
- The fix
- Chrysler will notify owners, and dealers will replace the ECM, free of charge. The recall began on December 21, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R52.
What owners say
Problems or none - your experience is exactly what the next buyer is looking for. Write it now
261 complaints about the 2016 Ram 2500
Newest first, as filed with NHTSA by owners. Page 5 of 11.
There is a current recall 17v821000 power train:automatic transmission:lever and linkage:column shift. I just bought this truck and was cleaning it when my kids pulled on the shifter in the driveway and it came out of park with no key in the ignition. I took the truck to dodge and they told me there was no recall and would not honor anything on line that I had found.
Tl* the contact owns a 2016 ram 2500. The contact stated that while operating the towing trailer brake, the trailer brake control failed to operate. The check wire connection and trailer disconnect error messages were displayed on the instrument panel. In addition, the contact stated that the vehicle downshifted, the brakes and low gear was selected to control the trailer brakes. The vehicle was taken to christopher's dodge ram (16655 w colfax ave, golden, co 80401) to be diagnosed. The vehicle was not repaired. The manufacturer was notified of the failure and provided a case number. The approximate failure mileage was 90,000. The vin was not provided.
I purchased my vehicle yesterday. Today I was driving it is stalled as I was pulling out into traffic I restarted it it drove fine another two miles. At which time is stalled again with no lights, no indications on. Sounds like some noise comes from the air box. Some kind of air noise comes from the passenger side of the engine when it happened
Tl* the contact owns a 2016 ram 2500. The contact received notification of nhtsa campaign number: 19v818000 (equipment, engine and engine cooling) and 20v036000 (power train) however the parts to do the repairs were not available. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repairs. The contact stated that the vehicle was taken three times to landmark dodge chrysler jeep ram, 6850 mt zion blvd, morrow, ga 30260, and was rejected to be serviced due to the parts not...
Read the full complaint
being available. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available for nhtsa campaign number: 19v818000 (equipment, engine and engine cooling), and part distribution disconnected for nhtsa campaign number: 20v036000 (power train).
Tl* the contact owns a 2016 ram 2500. The contact stated while driving at approximately 55 mph, the vehicle pulled to the right without warning. The contact stated that added effort was needed to steer the vehicle to regain control of the vehicle. The vehicle was taken to lithia chrysler dodge jeep ram fiat of spokane (10701 n newport hwy, spokane, wa 99218) to be diagnosed. The contact was informed that the steering requirements were in line with the manufacturer specifications. The manufacturer was made aware of the failure. The failure mileage was 5.
Tl* the contact owns a 2016 ram 2500. The contact stated while shifting the gears to park, the vehicle automatically reversed. The contact was able to resume the vehicle back to normal after a few days. The contact stated no warning light was illuminated. The vehicle was taken to local dealer napleton ellwood city chrysler dodge jeep ram located at 1000 lawrence ave, ellwood city, pa 16117 where it was diagnosed that the main wiring harness needed to be replaced. The vehicle had not been repaired as of yet. The manufacturer was notified of the failure and referred the contact to nhtsa. The failure mileage was approximately 12,000.
Tl* the contact owns a 2016 ram 2500. The contact received notification of nhtsa campaign number: 19v818000 (equipment, engine and engine cooling) and 20v036000 (power train) however, the parts to do the recall repairs were not available. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The contact called bergey's chrysler jeep dodge ram located at (408 harleysville pike, souderton, pa 18964 (215) 721-3470) but was not diagnosed or repaired. The contact did not experience a failure. The manufacturer was contacted however no further assistance was provided. Vin tool confirms parts not available.
Tl* the contact owns a 2016 ram 2500. While driving at 40 mph down a mountain the steering wheel failed to move. The contact stated that the floor mat was stuck on the steering shaft knuckle. There were no warning lights illuminated. The vehicle was taken to henry brown chrysler jeep dodge 1990 n pinal ave, casa grande, az 85122 (520) 836-2147 but was not diagnosed nor repaired. The manufacturer was contacted and informed of the failure. The failure mileage was 131,000. *Dt*jb
Tl* the contact owns a 2016 ram 2500. The contact stated the vehicle was repaired under nhtsa campaign number: 19v021000 (steering) serviced at dale willey chrysler dodge jeep ram located at 2300 w 29th terrace, lawrence, ks 66047. The contact while driving at 57 mph, the contact became aware that the steering wheel was not centered. The contact stated no warning light was illuminated. While inspecting the vehicle, the contact noticed the welded nut was fractured. The contact stated he was able to fix the fracture...
Read the full complaint
on his own. The dealer was contacted and was made aware of the failure. The contact stated the failure recurred. The manufacturer had not been informed of failure. The failure mileage was 62,917. *Dt
When driving my 2016 ram 2500 there is wobble or severe vibration. At highway speeds I sometimes have to fight with the steering. It feels like it is effecting the front of the truck. This is an alignment problem, however, in response to the drag link recall the dealer has welded the drag link in place preventing it from being aligned. Newer model trucks that were part of the recall had the part replaced but the older model (mine is 2016) were welded in place. In order to have alignment adjusted the weld will have...
Read the full complaint
to be broken and then rewelded. Everytime the weld is broken and redone to allow for alignment it weakens the metal. This is not safe but then again, neither is driving with the front end wobbling. In addition, none of the repair shops want to have anything to do with breaking the weld and aligning my truck due to the liability of doing such.
Tl* the contact owns a 2016 dodge ram 2500. Wheel studs sheared while driving. Vehicle was unsafe to operate possible crash due to loss of wheel stud support the contact stated that while driving at 65 mph, there was an abnormally loud sound coming from the front of the vehicle. The contact who work as a mechanic performed a self evaluation of the vehicle and became aware that five of the wheel studs on the driver's side front wheel had sheared off. The contact stated that the wheel bearings were...
Read the full complaint
previously replaced by burdick dodge chrysler jeep ram 5885 cir dr e #335, cicero, ny 13039 (315) 699-3846. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was 90,000.
Tl* the contact owns a 2016 ram 2500. The contact stated that on several occasions unknown warning lights flashed on and off on the instrument panel. The contact also stated that the windows failed to roll down while the ignition was in accessory mode. The contact also stated that several attempts were needed on occasions to start the vehicle. Additionally, while driving at an undisclosed speed, the steering wheel was turned to the right however, the vehicle went in the opposite direction. The contact referenced...
Read the full complaint
the failure to nhtsa campaign number: 19v021000 (steering). The vehicle was taken to (glenn polk autoplex - chrysler, dodge, jeep, ram glenn polk autoplex - chrysler, dodge, jeep, ram) for diagnosis and repairs however the failure recurred. The manufacturer was not made aware of this issue. The failure mileage was 62,000.
I have tried many times to get these numerous safety recall complied with and get no follow up from my local dealer! I took it in for a scheduled appointment and was told parts were on order. It's been far to long, I have checked in numerous times and get no help. Please find a place that can make my vehicle safe or make them buy it back from me! I don't want to die, or kill an innocent family! *Dt*jb
I called my dealer about a recent recall notice I received in the mail. They informed me that they would be welding the threads on my center drag link. This prevents the steering wheeel from ever being adjusted after an alignment. This now creates another safety issue with a steering wheel that will be way off center. So much for the 1- & 2 positions. This so called fix is is a disgrace! It calls for welding an adjustable part of the steering linkage rendering it non- adjustable when having the front end...
Read the full complaint
aligned in the future. Not to mention the effect of welding, potentially causing a problem with the integrity of the metal. The correct fix for this safety issue is to replace this steering linkage component, the entire drag link! Not do a "back yard, shade tree mechanic" weld job on the steering linkage of all things! I am appalled that nhtsa approved such a thing. Please revisit this issue and do the right thing. Require chrysler (fca us llc) to replace this defective part with the proper part. Note.... Chrysler is not welding the nuts on the drag links on trucks coming off the assembly line! They are coming off with proper, safe, adjustable drag links! I will die in this truck before I let fca weld anything on my steering linkage. Just so you know.
This is the tradesman model, which is the bare bones basic work truck. At night, when turning a 90 degree corner, left or right, one can not see the road or what might be coming because the headlights do not illuminate the road in a sharp turn. It is especially worrying when turning on a dark road from a stop sign. This has been like this since the truck was new.
Safety recall v06 / nhtsa 19v-021 drag link - january 25, 2019 this so called fix is abhorrent! It calls for welding an adjustable part of the steering linkage rendering it non-adjustable when having the front end aligned in the future. Not to mention the effect of welding, potentially causing a problem with the integrity of the metal. The correct fix for this safety issue is to replace this steering linkage component, the entire drag link! Not do a "back yard, shade tree mechanic" weld job on the steering...
Read the full complaint
linkage of all things! I am appalled that nhtsa approved such a thing. Please revisit this issue and do the right thing. Require chrysler (fca us llc) to replace this defective part with the proper part. Note.... Chrysler is not welding the nuts on the drag links on trucks coming off the assembly line! They are coming off with proper, safe, adjustable drag links! Signed, owner of a 2016 ram 2500 which I ordered and purchased new.
Tl* the contact owns a 2016 ram 2500. While driving with the cruise control engaged, the engine revved without warning. When the contact placed the gear shift lever in park, turned off and restarted the vehicle, the vehicle operated as intended. The vehicle was taken to larry h. Miller chrysler jeep tucson (7800 e 22nd st, tucson, az 85710 (520) 258-6000) where it was diagnosed that the speed control switch failed and needed to be replaced. The vehicle was repaired, but the failure recurred. The contact referenced...
Read the full complaint
nhtsa campaign number: 18v332000 (electrical system, vehicle speed control). The manufacturer was made aware of the failure and referred the contact to nhtsa to file a complaint. The failure mileage was approximately 83,888.
Clutch master cylinder failed while driving in 2nd gear, no clutch pressure, could not stop truck and it would not stall, I ended up turning key off after driving over curb on to sidewalk. This was while trying to stop for stopped cars at traffic light. Fortunately I was only moving at maybe 10 mph. Florida truck, 26k miles on it.
Tl* the contact owns a 2016 ram 2500. While traveling various speeds, the 4 wheel drive lever would shift independently and the "4 wheel drive shift in progress" warning message would illuminate. The contact took the vehicle to several dodge dealers, including athens dodge chrysler jeep ram (4145 atlanta hwy, athens, ga 30606), gwinnett chrysler dodge jeep ram (5054 ga-78, stone mountain, ga 30087), and akins dodge chrysler jeep ram (220 w may st, winder, ga 30680). The actuator and electrical harness were...
Read the full complaint
replaced; however, the failure continued. The manufacturer informed the contact to take the vehicle back to the original dealer to be serviced. The contact brought the vehicle back to athens dodge, but they were unable to duplicate the failure. The vehicle had not been repaired. The failure mileage was less than 10,000.
I am the owner of a 2016 ram 2500 withthe drag link recall. The proposed fix to the drag link does not correct the issue. Whle it provides a work around, there are compliants that even after the parts are welded owners experience this issue. This should be further investigated and the root cause which is defective parts should be replaced and not simply welded. I have contacted chrysler several times in an attempt to get the parts replace but they have indicated they will not comply with my request. I would like to know how this "fix" is acceptable by nhsta to make it safer and acceptable. Nhtsa campaign number: 19v021000
While driving with or without my travel trailer at different speeds a loud grounding noise is heard from under or toward the front dive train and has some feedback felt from the steering wheel sometimes the service 4wd lights up but not always I must slow down to a crawl ingage the 4wd stop back up cut off ignition restart sometimes it disengages 4wd and sometimes when I slow to a crawl a mechanical clunk can be heard and truck works normally . Durning the time the grinding sound is present the 4wd will not...
Read the full complaint
function and the 4wd indicater light will not come on. When this fisrt occurred the truck had around 4000 miles it was taken to the dealer conway chystler conway sc 29528 they replaced transfer case control module said it was fixed I picked it up it did it again about 5 miles from dealership I took it back they again replaced a part the axle locker actuator said it was fixed 7 days total in shop now for third time at 12000 miles its doing it again back to conway I have contacted fca to ask for a buyback this is very unsafe if this truck ingages 4wd pulling my camper on the interstate it could cause a crash so I now will no longer drive this truck unless I absolutly have to if no buyback is issued I will request a libility letter be issued to me from fca releasing me from any libility of this truck being sold or traded
Tl* the contact owns a 2016 ram 2500. While attempting to shift gears, the gear shifter separated from the steering column. The vehicle was taken to bryant motors (2901 south limit ave, sedalia, mo) where the failure was repaired. Later, while backing out of the garage, the transmission would not switch into the drive position. The vehicle would only drive in fourth gear and was taken back to the dealer who replaced the brake transmission shift interlock solenoid. On one occasion, after switching into the park...
Read the full complaint
position with the engine still running, the driver exited the vehicle. Moments later, the vehicle erroneously drove backwards and knocked the driver to the ground. The vehicle also struck two additional individuals who were positioned behind the vehicle. The vehicle then crashed into two parked vehicles and a motorcycle. The driver sustained neck and back injuries that required medical attention. A police report was not filed. The vehicle was towed. The cause the failure was not determined. The manufacturer was notified of the failures. The dealer was not contacted about the crash. The failure mileage was 36,000.*Dt
Tl* the contact owns a 2016 ram 2500. After starting the vehicle, the contact heard an abnormal clicking noise emerging from the engine. There were no warning indicators illuminated. The vehicle was towed to plaza chrysler dodge jeep ram (2077 hwy 44 w, inverness, fl 34453, (352) 726-1238) where it was diagnosed that the tension pulley fractured and snapped. The failure damaged the serpentine belt, water pump, and wiring harness. The manufacturer and dealer were not contacted. The failure mileage was 24,000. The vin was not available.
Tl* the contact owns a 2016 ram 2500. While driving 55 mph, the steering wheel turned to the right on its own. The contact stated that the right tires were wore down due to the failure. There were no warning indicators illuminated. The vin was included in nhtsa campaign number: 19v021000 (steering). The contact called quality chrysler of greenwood (located at 1525 sc-72, greenwood, sc 29649, (864) 642-0668) and was informed that they did not have anyone qualified to weld the nuts to the adjuster sleeve. The contact declined to have the remedy completed on the vehicle. The vehicle was not repaired. The manufacturer was notified. The failure mileage was 38,005.
Tl* the contact owns a 2016 ram 2500. While attempting to drive up a hill with a trailer in tow, the vehicle failed to accelerate. The contact also stated that the rear brakes failed to appropriately stop the vehicle. The contact took the vehicle to corwin chrysler dodge jeep ram fiat (located at 1025 w sunshine st, springfield, mo 65807, 417-862-9272) where the dealer stated the issue was related to the hill assist system. The vehicle was not diagnosed or repaired. The manufacturer was contacted and opened a case; however, the contact had not heard back from the manufacturer. The approximate failure mileage was 103,311.
Ram 2500: every year compared
| Year | Complaints | Recalls | Grade |
|---|---|---|---|
| 2020 | 162 | 10 | C |
| 2019 | 194 | 12 | C |
| 2018 | 2,614 | 10 | F |
| 2017 | 699 | 12 | F |
| 2016 | 261 | 14 | C |
| 2015 | 215 | 15 | C |
| 2014 | 345 | 16 | D |
| 2013 | 178 | 16 | C |
| 2012 | 283 | 5 | C |
2016 Ram 2500 vs rivals
| Vehicle | Complaints | Recalls | Grade | |
|---|---|---|---|---|
| 2016 Ram 2500 | 261 | 14 | C | |
| 2016 Ram 3500 | 134 | 16 | C | Compare |
| 2016 Chevrolet Silverado 2500 | 0 | 6 | D | Compare |
| 2016 Chevrolet Silverado 3500 | 0 | 7 | D | Compare |
| 2016 GMC Sierra 2500 | 0 | 6 | C | Compare |
| 2016 Ram 1500 | 1,568 | 17 | F | Compare |
| 2016 Ram Promaster | 71 | 15 | C | Compare |
| 2016 Ram Promaster City | 58 | 4 | F | Compare |
| 2016 Ram 5500 | 17 | 7 | C | Compare |
More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.
Questions about the 2016 Ram 2500
Does the 2016 Ram 2500 have any recalls?
Yes - NHTSA lists 14 recalls for the 2016 Ram 2500: inflator (January 2025); inflator (August 2021); latch (May 2019); connection (January 2019) and more. Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.
What are the most common problems with the 2016 Ram 2500?
By the complaints owners filed with NHTSA, the most common problem areas are the transmission & drivetrain (64), engine & cooling (57), steering (43).
How many complaints has the 2016 Ram 2500 had?
261 complaints have been filed with NHTSA, the first on October 22, 2015 and the latest on November 7, 2026. Of these, 16 describe a crash and 3 a fire, and together they report 10 injuries and 1 death.
Is the 2016 Ram 2500 a reliable vehicle?
Its Safety Index is 41 out of 100 (grade C: about as many problems as a typical Ram 2500 year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.
Which Ram 2500 years have the most complaints?
2018 (2,614), 2017 (699), 2014 (345). See every Ram 2500 year compared.
What should I do if my 2016 Ram 2500 has a problem?
If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.
Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data