- The problem
- Chrysler (FCA US LLC) is recalling certain 2016-2017 Ram 3500 Cab Chassis with a Gross Vehicle Weight Rating (GVWR) of less than 10,000 lbs, 2011-2017 Ram 3500, 4500 and 5500 Cab Chassis vehicles, 2009-2017 Ram 1500 and 2010-2017 Ram 2500 and 3500 pickup trucks, all equipped with a column shifter. Pushing the brake pedal for prolonged periods when the vehicle is running and in PARK may cause the Brake Transmission Shift Interlock (BTSI) pin to stick in the open position. With the pin in the open position, the transmission can be shifted out of PARK into any gear without pushing the brake pedal or having the key in the ignition.
- The risk
- Being able to shift the transmission without pushing the brake pedal and/or without a key in the ignition can increase the risk of an unintended vehicle rollaway that may result in personal injury or a crash.
- The fix
- Chrysler will notify owners, and dealers will update the vehicle software, inspect the BTSI, and, as necessary, replace it, free of charge. The recall began February 26, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T79.
Vehicle safety record
2011 Ram 2500 Problems, complaints & recalls
Owners have filed 298 complaints about the 2011 Ram 2500 with NHTSA, most often about the steering (210) and the engine & cooling (40). Those complaints describe 3 crashes, 7 fires and 4 injuries. It is covered by 4 recalls, the latest in December 2017 for the column shift. For comparison, the 2010 has 0 and the 2012 has 283.
NHTSA data checked
CAbout as many problems as a typical 2500 year, for its age
#36 most complained-about 2011 vehicle
- Complaints
- 298
- Recalls
- 4
- Crashes
- 3
- Fires
- 7
- Injuries
- 4
- Deaths
- 0
Most common 2011 Ram 2500 problems
Share of all 298 complaints. One complaint can name more than one area. Tap an area for its complaints and recalls.
2011 Ram 2500 recalls 4
Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do
- The problem
- Chrysler Group LLC (Chrysler) is recalling certain model year 2010-2014 Ram 2500, 3500, 4500, and 5500 trucks manufactured March 27, 2009, to September 5, 2013. In the affected vehicles, the electrical connectors of the diesel fuel heater may overheat.
- The risk
- If the connectors overheat, the fuel heater may leak fuel, increasing the risk of a fire.
- The fix
- Chrysler will notify owners, and dealers will replace the harness side connector with a silver plated beryllium copper terminal service kit, and inspect the fuel heater for leaks, replacing it as necessary, free of charge. Chrysler issued interim notification to owners on December 8, 2014. The recall began on April 27, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P65.
- The problem
- Chrysler Group LLC (Chrysler) is recalling certain model year 2008-2012 RAM 2500 4X4 and 3500 4X4 trucks, 2008-2012 Dodge RAM 3500 4x2 Cab Chassis, and model year 2008 Dodge RAM 1500 Mega Cab 4x4. The left tie rod assembly may break.
- The risk
- A failure of the tie rod assembly may result in a loss of steering control, increasing the risk of a crash.
- The fix
- Chrysler notified owners on January 16, 2014 that dealers would inspect vehicles and replace the steering linkage assembly, if necessary. On or about February 27, 2014, Chrysler ceased its recall remedy program due to parts quality concerns, and then re-initiated it on or about April 14, 2014. In July 2015, and under a consent order with NHTSA, the company agreed to offer owners three options for remedying their vehicles: perform the original remedy, offer to repurchase the vehicle at the fair market value plus 10%, or offer an additional incentive offer towards the purchase of a new Dodge, Jeep, Chrysler, or Fiat vehicle. Chrysler will notify owners of the new recall options in a letter expected to be mailed on August 31, 2015. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N49.
- The problem
- Chrysler is recalling certain model year 2008-2011 dodge ram 2500/3500 4x4, manufactured from february 14, 2008, through march 28, 2011; model year 2008-2011 dodge ram 3500 cab chassis 4x2, manufactured from february 14, 2008, through march 28, 2011; and model year 2008 dodge ram 1500 mega cab 4x4, manufactured from february 14, 2008, through august 15, 2008, because the left tie rod ball stud may fracture. This condition tends to occur during low speed parking lot type maneuvers when the customer is making a tight turn. Additionally, model year 2003-2008 dodge ram 2500/3500 vehicles may have received the affected tie rod assembly as a replacement part during normal service.
- The risk
- This condition could result in the potential loss of directional stability in the left hand front wheel, increasing the risk of a crash.
- The fix
- Dealers will inspect the tie rod ends for relative orientation and replace the left outer tie rod as required and perform a front end toe alignment as needed. This service will be performed free of charge. The safety recall began on october 3, 2011. Owners may contact chrysler at 1-800-853-1403.
What owners say
Problems or none - your experience is exactly what the next buyer is looking for. Write it now
298 complaints about the 2011 Ram 2500
Newest first, as filed with NHTSA by owners. Page 2 of 12.
Nhtsa recall 17v-821 this vehicle being offered for sale with clean history/carfax report. Recall not completed. Dealer: autonation dodge ram arapahoe 10743 east arapahoe rd., Englewood, co 80112 866 331-0726
Tl* the contact owns a 2011 ram 2500. While driving 65 mph, the contact noticed a vibration followed by a large explosion. The contact pulled the vehicle over to the side of the road. The inside of the vehicle filled with smoke and a hole was observed in the floor area along with flames. The fire was extinguished with a fire extinguisher. The contact called 911 where the police officer waited for the tow truck. A police report was not filed and there were no injuries. The vehicle was towed to the dealer (lithia...
Read the full complaint
chrysler, 7171 west canel dr, kennewick, washington 99336) where it was diagnosed that the front driveline became loose. The vehicle was traded in due to the failure. The manufacturer was notified and sent a represenative to do a report on the incident. Approximately two months later, the contact received a letter from the manufacturer stating that the failure was not their responsibility. The vin search revealed one recall, which was not in effect at the time of the failure. The failure mileage was 60,000. *Tt *tr
Tl* the contact owns a 2011 ram 2500. While driving approximately 80 mph, the vehicle lost power. The vehicle was coasted to the side of the road and restarted. The failure recurred several times. The vehicle was taken to ron sayer's chrysler jeep dodge in idaho falls, idaho 83401 (where it was diagnosed that the wind module needed to be replaced. The manufacturer was made aware of the failure and referred the contact to nhtsa. The vehicle was not repaired. The failure mileage was 153,000.
The win module makes the car shut off, without warning to the driver. This has happened many times going doe the free way at 81 mphs. It also happens in the city. You never know when it it going to happen. The truck literally shuts off because whenever. It also has issues starting back up.
Tl* the contact owns a 2011 ram 2500. While the vehicle was parked and the hood was lifted, the contact observed smoke coming from the engine area. The fire department was not contacted. The contact stated that the wires to the alternator were burned. The vehicle was not diagnosed or repaired. The contact called an unknown dealer and was informed that the repair cost was $400. The vin was not included in nhtsa campaign number: 17v435000 (electrical system). The manufacturer was notified of the failure and stated that there were no recalls associated with the vin. The failure mileage was approximately 250,200.
Check engine light has come on several times with codes p241a and p2196. I have replaced the o2 sensor 3 times within one year. I have been told that this is a common issue and have been told that it is the wring harness.
Exhaust tick tick noise. The manifold and the bolt hast rusted out. I can believe this is not a recall.
When I stop at traffic light/stop sign diesel fumes come through the vents and into the cab. Fumes are very strong. This all started the first year I owned the truck back in 2011 (bought new). Once you take off down the road with windows open fumes clear out but come back when you stop.
I became aware that the tipm module is defective. I notified dodge on this problem and even requested assistance on repair. On 11/03/17, was told dodge denied claim. In my opinion this may be a safety concern, since the tipm module controls fuel system, air bag deployment, wiper operations and a few other systems. I've noticed on the internet from dosge forums that alot of dodge and chrysler owners also had issuses with the tipm module. I was quoted for repairs around $1200.00 .
Death wobble - I was driving in heavy traffic on a 4 lane highway. I drove over a bridge expansion joint and suddenly the truck began shaking violently. I could not steer. I could not brake. We nearly collided with a highway divider and other vehicles. I had to coast down to 30 mph or so when it resolved itself.
Exhaust manifold bolts are cracked , 981 hours on the motor and 36,000 miles on the truck, the cab fills with exhaust smell, the bolts are defective see odi 10937913
Truck shut off while driving. Couldn't steer, couldn't turn, could barely stop. I was in the middle of a rotary with my 7 month old daughter in the car. Most likely the tipm was the cause because it started right up afterwards. No signs or warnings occurred before issue happened. *Tr
Tl* the contact owns a 2011 ram 2500. The contact stated that the bolts that attached the exhaust manifold to the vehicle had fractured. As a result, the exhaust manifold detached from the vehicle. The contact took the vehicle to the dealer where it was diagnosed that the bolts needed to be replaced, and the exhaust manifold may need to be replaced as well. This would not be determined until the replacement of the bolts was completed. The vehicle was not repaired. The manufacturer was made aware of the failure. The...
Read the full complaint
contact was informed that due to the fact that a plow was placed on the truck, the repair was not covered under warranty. The vin was unknown. The approximate failure mileage was 40,000. ...Updated 03/13/17 *bf *cn
Tl* the contact owns a 2011 ram 2500. While driving approximately 10 mph, the contact heard a pop sound from the front end of the vehicle. There were no warning indicators illuminated. The contact exited the vehicle and noticed that the front driver side tie rod was fractured. The vehicle was towed to the dealer. The vehicle was repaired per a manufacturer's recall. The manufacturer was notified of the failure. The contact also stated that the vehicle was repaired last year per the manufacturer's (n49) recall. The approximate failure mileage was 174,650.
Diesel fumes invade the cab of the truck when it is undergoing the "regeneration" phase of its emissions cycle. We are literally choking and holding our breath when this happens on a daily basis. The fumes are much worse if we have the heater or ac working at the time. It happens when we are moving but it is much more pronounced when the vehicle is stationary at a stop light or when parking. *Tr
Tl* the contact owns a 2011 ram 2500. While driving approximately 65 mph, the contact drove over a bump and the steering wheel shook violently. The vehicle vibrated and became very unstable. The vehicle was taken to the dealer where it was diagnosed that the stabilization bar failed and needed to be replaced. The vehicle was repaired, but the failure recurred. The manufacturer was not notified of the failure. The vin was unknown. The approximate failure mileage was 73,000.
While driving either pulling our 30ft 5th wheel or while not towing, hit rough spot in road truck shakes violently and is hard to control even braking! Has been serviced in may 2016 and changed torquestions bar. Same scenario has continued for 3 months only more often. Supposedly was fixed before 2 1/2 months trip to ak, bc & yt. Back again for same scenario as it occurs more often! Truck is always in motion and between 45 & 65mph when this occurs both country roads and freeway/highway! This is a serious uncontrollable scenario that could cause accident for driver and other cars on the road when this happens. Eugene, or
I had my truck towed into the dealership for a "no start". Problem did continue with the dealer a few times with no codes. The problem is that the truck would start and then when you try to restart vehicle, it would not start. Dealership concluded that it was a software issue, that needed to be updated with the some module in the truck. Unfortunately, I had ti pay for this updated, in which this problem should have been considered a factory issuse. Which in my opinion that the dodge corp. Should have covered this expense. I seen on the internet with other people having the same problem.
Upon activating the high beam head lights, engine will begin missing and eventually stall. Headlights will blink off and on. All dash lights and electrical systems will also fluctuate power (radio, wipers, tail lights, hazards, front parking lights and turn signals). All gauges on the dash will go dead. While driving on 7/22/2016 at approximately 9:15 pm the high beam head lights were activated. The engine began to miss and all electrical systems began to turn off, and then back on. The engine stalled at...
Read the full complaint
approx 65 mph leaving no power steering. Truck was able to be restarted once it was brought to rest on the shoulder. High beams could not be used or the problem would repeat. Make: ram (dodge) model: 2500 year: 2011 engine/powertrain: 6.7L cummins turbo diesel w/ 6 speed automatic.
Truck would not start due to faulty timp module. Luckily it was parked at home, but needed towed.
Tl* the contact owns a 2011 ram 2500. The contact received a recall repair for nhtsa campaign number: 13v529000 (steering), but the remedy did not provide a solution. The contact stated that there was an extensive wobble in the front of the vehicle. The vehicle was taken back to the dealer a second time where it was indicated that the parts needed to be replaced again. The dealer replaced the front tie rods, but the failure recurred. The vehicle was unable to be driven over 45 mph. The vehicle continued to wobble...
Read the full complaint
in the front, which was extremely unsafe while driving at highway speeds. The manufacturer was notified of the failure each time and provided no solution to the dealer to address the repair. The vehicle was taken back to the dealer for further inspection. The approximate failure mileage was 20,000.
While making a turn and applying the brake pedal, complete loss of power steering causing vehicle to cross center line of roadway and drive into oncoming traffic. Brake pedal also extremely hard to press (possibly loss of power braking at the same time). Steering returning to normal several seconds after releasing the brake pedal. This happened multiple times today, with shutting the vehicle off completely between occurrences of this failure.
Death wobble at highway speeds 2 recalls for tie rods have been peformed. This problem is continuing, most recently on 4/24/2016.
Dear sir or ma'am, I am writing you to report a severe problem that occurred to me on 3/5/16, and again on 4/9/16. I was traveling at approximately 65 mph on both occasions on washington state highways. The front end of my 2011 ram 2500 pick up began to shake violently. It was so intense that I was afraid that I might lose control of the vehicle. I slowed down and pulled to the side of the road and the problem stopped. After I got back on the road I traveled about a mile, and the problem occurred again. My...
Read the full complaint
wife brought the truck into a repair shop on 3/7/16 to see if there was a problem with the tires or suspension. The shop said the tires were balanced and that they did not find any obvious problem with the suspension. After a quick internet search I discovered a number of people describing the exact problem that I had experienced. They referred to it as the 'dodge death wobble' much to my surprise, this does not seem to be an isolated incident. It seems to be caused by the steering design ('y' type vs. 'T' type?) I am hoping that you will initiate an investigation into this problem and ultimately mandate that fca us llc (dodge) issue a recall for all vehicles affected by this design flaw before someone gets hurt. I contacted dodge corporate hq and I have attached their response.
Tl* the contact owns a 2011 ram 2500. While driving approximately 65 mph, the vehicle drove over a bump and the steering wheel shook violently. The vehicle vibrated and caused the vehicle to become very unstable. After reducing the speed to 30 mph, the vehicle drove normally. The failure occurred on two other occasions. The cause of the failure was not diagnosed. The vehicle was not repaired. The manufacturer was not notified. The failure mileage was 110,000.
Ram 2500: every year compared
All 2500 years2011 Ram 2500 vs rivals
| Vehicle | Complaints | Recalls | Grade | |
|---|---|---|---|---|
| 2011 Ram 2500 | 298 | 4 | C | |
| 2011 Ford F-250 | 0 | 2 | A | Compare |
| 2011 Ford F-350 | 0 | 4 | C | Compare |
| 2011 Chevrolet Silverado 2500 | 0 | 4 | C | Compare |
| 2011 Chevrolet Silverado 3500 | 0 | 5 | C | Compare |
| 2011 GMC Sierra 2500 | 0 | 4 | C | Compare |
| 2011 Ram 3500 | 0 | 5 | A | Compare |
| 2011 Ram 1500 | 689 | 4 | C | Compare |
| 2011 Ram 1500 Crew | 689 | 0 | C | Compare |
More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.
Questions about the 2011 Ram 2500
Does the 2011 Ram 2500 have any recalls?
Yes - NHTSA lists 4 recalls for the 2011 Ram 2500: column shift (December 2017); diesel (October 2014); tie rod assembly (November 2013); tie rod assembly (July 2011). Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.
What are the most common problems with the 2011 Ram 2500?
By the complaints owners filed with NHTSA, the most common problem areas are the steering (210), engine & cooling (40), suspension (37).
How many complaints has the 2011 Ram 2500 had?
298 complaints have been filed with NHTSA, the first on January 24, 2011 and the latest on September 20, 2026. Of these, 3 describe a crash and 7 a fire, and together they report 4 injuries and 0 deaths.
Is the 2011 Ram 2500 a reliable vehicle?
Its Safety Index is 45 out of 100 (grade C: about as many problems as a typical Ram 2500 year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.
Which Ram 2500 years have the most complaints?
2018 (2,614), 2017 (699), 2014 (345). See every Ram 2500 year compared.
What should I do if my 2011 Ram 2500 has a problem?
If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.
Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data