On certain passenger vehicles, the rear quarter glass attaching fasteners may pull through their mounts and allow the glass to separate from the vehicle.
Updated daily from NHTSA
Latest vehicle recalls
38 recalls announced in the last 30 days. Newest first - each one shows the problem, the risk, the free fix and every vehicle it covers.
On certain motorcycles, the weld between the side stand and the frame bottom section was not positioned properly. The load-bearing capability of the side stand is affected. As a result, the side stand could fail.
On certain crew cab model trucks, the seat back shape may be such that there may not be sufficient webbing on the retractor spool for the rear center seat belt to release from the automatic locking mode (alr) after it is engaged and the seat belt is...
Certain passenger vehicles fail to conform to the requirements of federal motor vehicle safety standard no. 208, 'Occupant crash protection.' The right front passenger seats in these vehicles are built with a passenger air bag sensing system. When tested...
Certain cardone master cylinders with part numbers 10-2925, 10-2987, 10-2987mza, 10-3083, 11-3015, 11-3042, 11-3044, 11-3045, 11-3047, 11-3064, and 11-3156, and with date codes lower than dca7078 sold as replacement equipment for use on the vehicles listed...
On certain travel and fifth wheel trailers equipped with hickory springs 'big easy triple steps,' an improper engagement of the bottom step pivot arm with the formed stop edge of the middle step support bracket can result in the bottom step rotating to an...
Certain fifth wheel and travel trailers equipped with a two-door refrigerator, manufactured by the dometic corporation, may have a defect in certain tubing in the refrigerator which could allow pressurized flammable coolant solution to be released into an...
Certain fifth wheel and travel trailers equipped with a two-door refrigerator, manufactured by the dometic corporation, may have a defect in certain tubing in the refrigerator which could allow pressurized flammable coolant solution to be released into an...
Certain my 1994 through 2002 thomas built minotour, fs-65, mvp-ef, er, and hdx-ef school buses manufactured between january 23, 1994, and april 15, 2002. The seat belt may chafe on the edge of a metal bracket and wear prematurely.
On certain trailer mounted aerial work platform booms, the hold down bracket that secures the mast/upper structure for transport may become damaged or loose over time. If the mast hold-down bracket sustains structural damage, it may no longer be capable of...
On certain trucks equipped with a 6.4L diesel engine, insufficient clearance of the battery positive (b+) wire to the right hand splash shield bolt may result in the battery b+ wire contacting the splash shield bolt.
On certain trucks equipped with a 6.4L diesel engine, excessive temperatures in the diesel particulate filter in the exhaust system may result from excess hydrocarbons in the exhaust.
On certain trucks, the cylinder head idler gear bushing may have been improperly machined, causing excessive stress on the cylinder head idler gear shaft. Continued operating in this condition could cause the idler gear shaft flange to break and generate...
Certain my 2000 through 2003 thomas built hdx and mvp-er school buses manufactured between april 23, 2000, and november 14, 2003. The service air brake pedal, for both non-adjustable and adjustable brake pedals, may contact the front structure on the bus...
Certain my 2006 and 2007 thomas built minotour, fs-65, c2, hdx, and ef school buses manufactured between january 6 and september 6, 2006, equipped with ricon wheelchair platform lift models s2003, s2005, s2010, s5503, s5505, s5510, k2003, k2005, k2010, k5503...
On certain transfer trailer chassis, the drawbar hinge assemblies at the front of the turntable may have been incorrectly assembled or improperly tightened during assembly.
Certain fifth wheel and travel trailers equipped with a two-door refrigerator, manufactured by the dometic corporation, may have a defect in certain tubing in the refrigerator which could allow pressurized flammable coolant solution to be released into an...
On certain trucks, the axle housings may have been manufactured with steel that was out of specification which could result in a fatigue failure over time.
On certain motorcycles, the crankcase breather separator may be defected. During the molding process, the breather passage may have been blocked by a thin layer of the injected plastic material. This blockage will create a build-up of pressure inside the...
On certain trucks, the axle housings may have been manufactured with steel that was out of specification which could result in a fatigue failure over time.